Shock pads are made of polyurethane and rubber. They are very similar to risers but vary in the fact that their sole purpose is to cushion the board from the trucks. Since the trucks are metal and the board wood, whenever the board hits the ground after doing a trick, the energy goes through the truck to the board ─ this has caused boards to crack, split, or even break in half, and shock pads were created to prevent this.
The laws for skateboarding helmets vary from state to state. Many states require that skaters wear a helmet under a certain age, and some states like California make all skaters under 18 wear a CPSC Certified helmet at all times. CSPC skateboard helmets usually have an EPS protective liner that meets the safety standards for skateboarding. Make sure you check your state's regulations before ordering.
In 1978, Alan Gelfand, who was given his nickname "Ollie" by Scott Goodman, learned to perform no-handed aerials in bowls and pools using a gentle raising of the nose and scooping motion to keep the board with the feet. There are numerous references to Alan Gelfand's Ollie with most notably pictures in the 1970s skateboarding magazine "Skateboarder".
The Powell Golden Dragon 2 Skateboard is an affordable and complete skateboard for the beginners and also for the advanced skaters. It has high-rebound, hand-cast polyurethane wheels to give you a great roll and grip. It measures 7.5 inches wide with a colorful screen-printed bottom. It is made in China and has an average rating of 4.2 on Amazon.
Cruiser - The name says it all. If you are looking to cruise around town then this is the right complete skateboard for you. These decks vary in length from between 20 inches all the way up to about 40 inches. The wheel diameters usually start at about 55 millimeters and use a much softer urethane than the previous Popsicle decks. These also come with all of the above but the decks do not always need grip tape. Some of the decks are plastic or composite material with grooves or gripping built directly into the deck mold.
When I was about 10, I broke my first skateboard by riding it into a ditch. A decade later, in college, I broke another skateboard within an hour of owning it (surely a record) in a short-lived attempt at doing an ollie. (Surprisingly, the store accepted a return on that board even though it was in two pieces.) Then I was gifted a really nice, high-quality skateboard. The first thing I did with it was ride it down a big hill, a valiant but ill-fated adventure which ended with me jumping off the skateboard, rolling down the grass, and arriving scraped up, deflated, and rather disoriented near the entrance to my college cafeteria. (In my defense, the wheels and ball-bearings on that skateboard had been pre-lubricated to minimize friction, and why would anyone do that, that's just crazy.)
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it.
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them . Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
With Enkeeo 22 Inch Cruiser Skateboards, you can cruise in style. It has a dimension of 22 x 6 inches. It comes with 3″ Black Coated Habitat trucks, Black 60mm Smooth wheels, and Abec11 bearings. It’s ready to ride and you can even personalize the tail of the board for free with a limitation of 10 Characters only. It has 30 days warranty and is manufactured in California. It has a perfect 5 rating on Amazon.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.