The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve
My fiancee purchased this via my account and he says that it has good concave shape and pop.Assembling was fairly simple, easier if you have a box cutter on hand to help with laying the grip tape. The deck was the best part but the bearings were good too. He thought the bushings were the worst, after about two hours of skating, both bushings were crushed and stuck in one direction. He's been skating for almost 13 years. Hope this helps!
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.

Unlike some deck options, which are completely bare, the Bamboo Skateboards Galaxy Series Cosmic Cloud Skateboard Deck features heat-stamped artwork on the underside of the board, including several geometric and interstellar designs, including a beautiful nebula. Bamboo Skateboards claims these boards last their customers three weeks longer than other decks. The company sells the boards in three sizes: 7.75-by-31.5-inches, 8-by-31.75-inches and 8.25-by-32-inches.

Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.
The Powell Golden Dragon 2 Skateboard is an affordable and complete skateboard for the beginners and also for the advanced skaters.  It has high-rebound, hand-cast polyurethane wheels to give you a great roll and grip.  It measures 7.5 inches wide with a colorful screen-printed bottom.  It is made in China and has an average rating of 4.2 on Amazon.
Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.

If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.


In fact, we can work out how you need to steer the skateboard. Tracker has a nice feature that we'll call 'force arrows'. These arrows show you how much force acts on an object at every instant, and in which direction the force acts. So for example, if you were to kick a ball into the air, while the ball was mid-flight, this arrow would always point down and be the same length, even though the ball is moving forward. That's because the only force acting on the ball is gravity, which pulls it straight down, and acts with a constant strength. (For those of you who've studied physics, these arrows denote the acceleration of the center of mass, which by Newton's second law is proportional to the net force acting on the skateboard.)
Skateboard hardware is used to connect the skateboard trucks to the skateboard deck. Skateboard hardware refers to the bolts and locknuts used when building a board. The bolts can have an Allen or Phillips head. Skateboard hardware comes in many different lengths, and often includes one different colored bolt so that the rider can mark the nose of their board.
Mounting hardware is a set of eight 10-32 UNF bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks (and any type of risers) to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard. Hardware is available in various lengths for mounting trucks with or without risers.

If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.
Hey Isak I’m a 46 year old Street Skateboarder recently started Skateboarding a few months back I’m trying to get my Ollies down I’ve stopped Skating for the last couple of weeks because I was getting frustrated with not getting my Ollies I was in a funk confidence slightly knocked so I’m thinking of going Street Skating all day tomorrow and not caring about what others think it’s all in my mind I know I can do this but may mind says I’m going to slam I skate alone but shouldn’t make any difference I need help with motivation somebody give me a kick up the ass you are never to old to start Skateboarding help dudes?! Mark UK. 🙂
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car.  It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings.  It is ready to use and you can easily store it in your backpack.  It has an average rating of 4.5 on Amazon.
×