The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.
Skateboarding started in California in the 1950s. The first skateboards were made from roller skates (attached to a board). Skateboarding gained in popularity because of surfing; in fact, skateboarding was initially referred to as "sidewalk surfing". Initially, skateboards were handmade from wooden boxes and planks by individuals. As the sport became more popular, companies started manufacturing skateboards. Boards are also continuing to evolve as companies try to make them lighter and stronger or improve their performance.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
I’ve been skating for about 3-4 years, I can kickflip, pop shuv it, front shuv, 180 and almost heelflips. I can ollie and used to be very good at them and could get them clean, but when I started practicing kickflips, it made my slide all weird. I can still ollie ( though it’s not as clean) but now when I ollie I slide with my pinky toe and that region, instead of the side of my foot. How can I fix my slide? When I try practicing sliding with the side of my foot, it doesnt feel like I can turn my foot that far towards the board and when I do it slowly to see what im doing, i still slide with my toes.Thank you.
This set-up is awesome for its price!!!! The wheels are nice and smooth (a little too big for my liking, but still good). The bearings are average (I replaced them with bones REDS). The trucks are nice and sturdy, but the bushings are kinda weak. The board is AUTHENTIC and of good dimensions. Finally, the griptape...they're all pretty much the same it's just the brand name that's different, so it doesn't matter it's all good. I would buy from this seller over and over again!!!!!!!
Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.
The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
Crouch down – While you’re standing on the board with your feet in the right position, crouch down closer towards the board. Don’t turn into a hunchback here; keep your back as straight as possible and don’t stick your rear out too far off the board, otherwise you’ll mess the whole thing up. Stay on the balls of your feet too; if you’re more on your toes, you’ll actually move the board in air and land off of it, and no one wants that. If you need to readjust your feet before you jump, just do a little micro-jump to reposition your feet, or shuffle into position. The first way is easier and faster, the second is more awkward and can mess up your shoes.
If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.
The DAPANLA deck is 7.5-by-31-inches in size, on the smaller side of good quality, real skateboard decks, which makes it ideal for smaller and shorter people. Unlike many decks on the market today, the DAPANLA deck comes with non-slip grip tape on the top. The underside of the deck is similarly decorated, with a range of DAPANLA designs including the fun cartoon avocado board that is sure to turn a few heads for its uniqueness.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it.