Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
The switch stance ollie uses a similar body motion, but the nollie is subtly distinct: For one, the rider is always moving forward, with the body positioned in a nollie stance--closer to the nose and with the front foot on the nose. Secondly the rider usually postures the body differently so as to compensate for this stance with respect to the forward motion. The rider presses the nose down using their front foot to engage the "pop" motion in order for the board to rise. This is In contrast to a "Fakie Ollie" where the pop motion is performed by the rear foot on the tail, similarly to a normal Ollie, however the rider is traveling backwards when performing a Fakie Ollie. Where in a Nollie the rider is traveling forward with their front foot on the nose to apply the initial force "pop".
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.
Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!
James Haden is one of the owners of the Skateboarder community, together with Nash Gibson – his co-owner. He works as a full-time copywriter for a private company and also a true adventurer. He is an avid reader, writer, traveler, and extreme sports junkie. During his free time, he researches interesting content for their blog and continuously writes for their audience.
Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie
Radiate Ride Good Skateboards are made of 7-ply maple construction with epoxy resin glue. It features 356A heat-treated cast aluminum high performance 5.0 trucks with grade 8 kingpins and axles. The super high rebound 99A PU wheels with grooved running surface provide better traction and abrasion resistance. The Abec 5 high precision speed bearings offer precision performance and a smooth ride. It has an 80 grit durable color matched grip tape with transparency. It is completely assembled and ready to go. This product has a 4.3 rating on Amazon.
When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.
If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
500AlmostAluminatiArborBambooBirdhouseBlindBonzingCometCreatureDarkstarDB LongboardsDevilleDogtownDusters CaliforniaElementEnjoiEverseshFlipFocusFoundationGlobeGoldCoastGravityHabitatJartKebbekKrookedLandyachtzLaybackLushMadridMakahaMoonshine MFGOmenPennyPlan BPowell PeraltaPrism SkatePunkedRayneRealRememberRivieraRoad RiderSan ClementeSanta CruzSector 9Suicidal SkatesToy MachineWarehouseZ-FlexZero
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.