The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

The type of skating the rider wants to do will inform the board choice, which sometimes involves skating a non-popsicle shaped board. But if you are just starting out, you can simply start with the traditional popsicle shaped deck that you probably recognize. As you skate more and get to know what shapes you like or what kind of skateboarding you enjoy best, your decisions will take into account for company, shape, width, and style of riding. Until then, choosing a board by its graphic is totally acceptable. For an overview on types of skateboard decks and riding styles, check out our Skateboard Decks Section in our Buyer’s Guide. Once you find a deck you like, you can simply select the default wheels, trucks, bearings and grip tape or you have the option to make it a complete.
Go for the low truck profile if you want to obtain additional stability when you do flip tricks. It also works well for small wheels. The mid-sized trucks are good for all-around use, especially in streets and parks. You can also choose the high-sized trucks that are good for carving and cruising, which is the reason why they are perfect for huge wheels.

The Wasatch Imports Good Skateboards is the ultimate compact and complete street board that is ready-to-go. It is great for exercise and fun. It is very portable and perfect for all skill levels. It has a variety of awesome vintage color combinations that you can choose from. It is made of topline construction, with a high-density plastic deck, 59mm super smooth wheels, ABEC7 bearings, and solid aluminum trucks. It measures 22″ long and 6″ wide and weighs 4 pounds. It has a  full manufacturer’s lifetime warranty on all parts, pieces, and materials. It has a weight limit of 200 pounds which can ensure that bigger skaters can join the fun.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!
Ancheer 31″ Pro Skateboards are made of 7-ply maple wood and finished with anti-slip grip tape.  It includes 60mm PU wheels ideal for riders who want to carve out sections, obtain speed and higher off the ground for tricks. It features 6″ Tony Hawk Signature aluminum trucks and 32″ long deck with double kick tail which is ideal for perfecting your favorite tricks.  It comes with ABEC-7 skateboard bearings.  It has style and quality which is expected from the most influential skateboarders of all time.  It is one of the best-rated skateboards on Amazon with a rating of 4.8.

The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.
An Ollie is basically an upward/forward jumping trick. The name “ollie” comes from the nickname of Alan Gelfand who created the ollie in 1976. The ollie was then modified for flat-ground use by Rodney Mullen in 1982, and it is this flat-ground version of the ollie which is most commonly referred to as the ‘ollie’ today. The ollie is arguably the most important trick in skateboarding because it is the foundation of the majority of skateboard tricks which require lift. When you want to do a trick like the kickflip, when you want to get onto something like a ledge, or down something like a set of stairs, or try handrails, the ability to ollie is a necessity. Therefore the ability to ollie high and with good control is critical to your total skateboarding skill-set.
Pop the board in the air – The reason you jump up into the air in the first place is because you’re slamming the back end into the ground (don’t worry, your board is made to take the abuse). It’s the same motion you would do if you were standing near the board and wanted to pop the board up into your hands, except this time, you’re standing on top of it. As soon as you feel the board pop into the ground, kick your front foot up into the air at the same time. The timing on this is important: kick too early and you won’t go anywhere, kick too late and your board will fly out from underneath you.
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
500AlmostAluminatiArborBambooBirdhouseBlindBonzingCometCreatureDarkstarDB LongboardsDevilleDogtownDusters CaliforniaElementEnjoiEverseshFlipFocusFoundationGlobeGoldCoastGravityHabitatJartKebbekKrookedLandyachtzLaybackLushMadridMakahaMoonshine MFGOmenPennyPlan BPowell PeraltaPrism SkatePunkedRayneRealRememberRivieraRoad RiderSan ClementeSanta CruzSector 9Suicidal SkatesToy MachineWarehouseZ-FlexZero
Krown burst on to the skate scene back in 1996 with the idea to provide a high quality skateboard to the rider on a budget. Krown recognized a big gap between the $20 big box retail skateboard and the $150 professional grade skateboard. The boards at big box retail stores have plastic wheels and don’t even roll! Krown’s idea to bring a price-point skateboard to the market that actually functions as a skateboard has proven to be successful after more than 20 years. With more than 20 years of industry knowledge and knowhow, Krown is able to source the best parts at the best prices, which allows Krown to pass the savings on to the consumer. This expertise has allowed Krown to venture into the world of skateboards, longboards, helmets, pads, and even tools. Krown is the best place to start for beginner and intermediate riders!
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.
Pop the board in the air – The reason you jump up into the air in the first place is because you’re slamming the back end into the ground (don’t worry, your board is made to take the abuse). It’s the same motion you would do if you were standing near the board and wanted to pop the board up into your hands, except this time, you’re standing on top of it. As soon as you feel the board pop into the ground, kick your front foot up into the air at the same time. The timing on this is important: kick too early and you won’t go anywhere, kick too late and your board will fly out from underneath you.
Learning to skateboard takes dedication.   If you want to learn fast, it helps if you have an order and a strategy.   Many new skateboarders try to learn to Ollie or learn to kickfliip before they are ready.  They will try to Ollie before they can effectively push their skateboard or even do a kickturn.   This often leads to frustration and even giving up.   So, for you parents and Noobs out there, here is an outline of some of the very first things you should learn to do on a skateboard.
Skateboarding, in one form or another, has been around since the late 1950’s when the first brave pioneer first attached roller skate wheels to a piece of wood. As skateboarding progressed to mimic surfing, skateboards evolved with the style of riding. Skateboards grew and changed shapes as riders experimented with everything from plastic to fiberglass to aluminum constructions - all in an effort to push what was possible. Like most sports or art forms, progression is at the heart of skateboard innovation.
With Enkeeo 22 Inch Cruiser Skateboards, you can cruise in style.  It has a dimension of 22 x 6 inches.  It comes with 3″ Black Coated Habitat trucks, Black 60mm Smooth wheels, and Abec11 bearings. It’s ready to ride and you can even personalize the tail of the board for free with a limitation of 10 Characters only. It has 30 days warranty and is manufactured in California.  It has a perfect 5 rating on Amazon.

I have been doing ollie’s for about a year to a year and a halve, but thats not the problem. My problem is the board turns when i ollie, i cant help it, i am starting to go into harder ground (ollying off ledges and ollying stairs) but i cant land and ride away because my board has turned in a 45 degree angle and it jerks me off the board, Please help in all you can, cheers mate.


The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
×