From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Cheap Hoverboard Drones Drones with Camera Electric Scooter Electric Skateboard Freeboard Gifts for Skateboarders GoPro Alternative Cameras Headphones Hoverboard Laws How to Ride a Snakeboard Longboard Longboards Mini Segway Mopeds Mopeds for Sale Quadcopters Quadcopters with Camera Ripstick Rollerblades Roller Skates Self Balancing Board Self Balancing Scooter Self Balancing Unicycle Skate 3 Skateboard Skateboard Backpacks skateboard d Skateboard Decks Skateboard Girls Skateboarding Tricks Skateboard Quotes Skateboard Rack Skateboards Skateboard Trucks Skatecycles Skate Game Skate Logos Skate Shoes Ski Jackets Smart Electric Scooter Snakeboard Unicycle Scooter Vans Waveboards

Skateboards can be bought online and in your local stores.  However, choosing a good skateboard can be challenging.  If you are a beginner there are a lot of things that you have to consider.  Aside from the cost, you should also check the entire board such as the wheels, the deck, the trucks, and others.  Here, we have compiled the best skateboards for sale that you can choose from right now.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!
My problem is that my board always lands crooked when I Ollie. The worst thing is that I even tell myself to “keep your shoulders straight” while I’m doing the Ollie and I still land crooked. I think it’s just hard for people to grasp the simple fact that everything on a skateboard has to be done horizontally which is odd because people don’t walk sideways. We walk straight. Like roller blading for example…. it’s easier for me to roller blade because I’m used to walking and running obviously except with a skateboard everything is as if you were hopping over a fence sideways. Skateboarding is tough.

Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.


If you are looking to buy a pre-built complete for yourself or someone else, CCS has pre-built complete skateboards for sale, too. This is by far the fastest way to buy a skateboard complete and often times the least expensive. Because we work directly with the manufacturer's, the cheapest skateboard complete for sale is our CCS Logo Skateboard Complete.
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.

To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.

4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
Before learning it, do have your riding basics down. Meaning you are very comfortable riding it around and doing kickturns and not be pushing mongo. Best to learn it whilst stationary with your wheels on a crack so that you don't move and slip out so much. I don't recommend doing it on grass or carpet cos when you pop the tail, it's gonna be absorbed by the floor and when you start doing it on pavement, your muscles will memorize a different way of doing it. So nope, no easy way out i guess.
You can learn to ollie while standing stationary, or while your skateboard is rolling. Ollying while standing still works the same way as while rolling, but I think rolling ollies are easier than stationary ollies. If you would like to learn to ollie with your skateboard stationary, you can place your skateboard on some carpet or grass to keep it from rolling. If you prefer to learn to ollie while your skateboard is rolling, don’t go very fast at the start. Whichever way you learn to ollie, once you feel comfortable you should try to ollie the other way as well.
×