The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.

In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
New shoes + new board + new grip tape isn’t going to help anything you need to reed what is above bro its an easy how to….bend down push your back foot down make sure the tail snaps off the ground and slid your front foot forward in one swift motion you’ll get it…iv been skating 11 years and its taken me this long to finally land kick flips regularly heel flips and varials my tres are 1 outa 10 still so I practice every day and someday ill be able to land it regularly when I want skateboarding takes alot of patients ALOT so dont think you’re going to learn everything over night just sayin
Taotao Girls Skateboards comply to United State Consumer Product Safety Commission (CPSC) Standard.  It has a 24″ X 6″ Maple Double Kickside Deck. It features 608Z Bearings, 3.5″ Plastic Truck & Base, and 50 x 30 mm PVC Wheels.  The Safety helmet, Knee and  Elbow Pads also comply to CPSC Standard.  It has a Cool Pink Aloha Graphic Design with an Amazon rating of 4.3.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.  
I’ve been skating for about 3-4 years, I can kickflip, pop shuv it, front shuv, 180 and almost heelflips. I can ollie and used to be very good at them and could get them clean, but when I started practicing kickflips, it made my slide all weird. I can still ollie ( though it’s not as clean) but now when I ollie I slide with my pinky toe and that region, instead of the side of my foot. How can I fix my slide? When I try practicing sliding with the side of my foot, it doesnt feel like I can turn my foot that far towards the board and when I do it slowly to see what im doing, i still slide with my toes.Thank you.
In most cases, it is available in black but you can also find clear ones that are ideal for you if you want to show a specific logo. Another nice choice that you have is the die-cut grip tape, which works in displaying the color or design of the deck beneath it. Make sure to choose a grip tape at a size, which perfectly suits your skateboard’s deck.

The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
One foot on the tail, (by foot I mean the ball of the foot which is just behind the big toe) the other foot is about an inch behind the bolts(screws) for the front truck. Basically, the back foot quickly pushes the tail down, and right when the tail of the board strikes the ground, the back foot jumps up… the tail of the board will follow up with the foot when the front foot slides forward slightly, which pivots the tail of the board upwards. Since the front truck comes off the ground first, getting the back truck up is the trick.
A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.
Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.  
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
The longboard, a common variant of the skateboard, is used for higher speed and rough surface boarding, and they are much more expensive. "Old school" boards (those made in the 1970s–80s or modern boards that mimic their shape) are generally wider and often have only one kicktail. Variants of the 1970s often have little or no concavity, whereas 1980s models have deeper concavities and steeper kicktails.[7]
Maybe you're new to skateboarding. We have lots of complete skateboards or longboards to get you started. All of our skateboard and longboard completes come fully assembled, so you can hit the streets without any of the hassle—try an Enjoi skateboard complete or check out our selection of Sector 9 longboard and skateboard completes. Or maybe you're an experienced skater looking to update and customize your ride. You probably want to start with the perfect skateboard deck before you do anything else. We carry high-quality skate decks to keep you steady and balanced while you bomb, slide, and carve the streets. We also have a variety of longboard decks in stock if you're looking for a smooth ride for cruising or commuting.
If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
In 1978, Alan Gelfand, who was given his nickname "Ollie" by Scott Goodman, learned to perform no-handed aerials in bowls and pools using a gentle raising of the nose and scooping motion to keep the board with the feet.[2][3] There are numerous references to Alan Gelfand's Ollie with most notably pictures in the 1970s skateboarding magazine "Skateboarder".
Before learning it, do have your riding basics down. Meaning you are very comfortable riding it around and doing kickturns and not be pushing mongo. Best to learn it whilst stationary with your wheels on a crack so that you don't move and slip out so much. I don't recommend doing it on grass or carpet cos when you pop the tail, it's gonna be absorbed by the floor and when you start doing it on pavement, your muscles will memorize a different way of doing it. So nope, no easy way out i guess.
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
No I don’t believe that. You have to feel your board with your toes and feel the shape that the board Under the bottom of your feet and then master the pop with this newly formed connection. Faster faster and more guts are needed. When you are going as fast as you can go and can Ollie perfectly with complete consistency you’ll Ollie everywhere even in the cold cold winter.
Level out on the way down – Before you start to head back towards the safety of the earth, level your feet out as the board begins to fall. If you’re trying to jump a gap on your board, this will help you keep going straight and maintain your momentum. Alternatively, you can land on your nose or tail and perform a manual out of the jump, but those are pretty advanced moves. Might want to wait until those little pink training wheels are off your board first.
!function(e){function n(t){if(r[t])return r[t].exports;var i=r[t]={i:t,l:!1,exports:{}};return e[t].call(i.exports,i,i.exports,n),i.l=!0,i.exports}var t=window.webpackJsonp;window.webpackJsonp=function(n,r,o){for(var s,a,l=0,u=[];l1)for(var t=1;td)return!1;if(p>f)return!1;var e=window.require.hasModule("shared/browser")&&window.require("shared/browser");return!e||!e.opera}function a(){var e="";return window.Q.sendErrorsToWeblogger&&"quora.com"==window.Q.subdomainSuffix&&(e+=[window.location.protocol,"//log.quora.com"].join("")),e+="/ajax/log_errors_3RD_PARTY_POST"}function l(){var e=o(h);h=[],0!==e.length&&c(a(),{errors:JSON.stringify(e)})}var u=t("./third_party/tracekit.js"),c=t("./shared/basicrpc.js").rpc;u.remoteFetching=!1,u.collectWindowErrors=!0,u.report.subscribe(r);var f=10,d=window.Q&&window.Q.errorSamplingRate||1,h=[],p=0,m=i(l,1e3),w=window.console&&!(window.NODE_JS&&window.UNIT_TEST);n.report=function(e){try{w&&console.error(e.stack||e),u.report(e)}catch(e){}};var y=function(e,n,t){r({name:n,message:t,source:e,stack:u.computeStackTrace.ofCaller().stack||[]}),w&&console.error(t)};n.logJsError=y.bind(null,"js"),n.logMobileJsError=y.bind(null,"mobile_js")},"./shared/globals.js":function(e,n,t){var r=t("./shared/links.js");(window.Q=window.Q||{}).openUrl=function(e,n){var t=e.href;return r.linkClicked(t,n),window.open(t).opener=null,!1}},"./shared/links.js":function(e,n){var t=[];n.onLinkClick=function(e){t.push(e)},n.linkClicked=function(e,n){for(var r=0;r>>0;if("function"!=typeof e)throw new TypeError;for(arguments.length>1&&(t=n),r=0;r>>0,r=arguments.length>=2?arguments[1]:void 0,i=0;i>>0;if(0===i)return-1;var o=+n||0;if(Math.abs(o)===Infinity&&(o=0),o>=i)return-1;for(t=Math.max(o>=0?o:i-Math.abs(o),0);t>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=0;r>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=new Array(s),i=0;i>>0;if("function"!=typeof e)throw new TypeError;for(var r=[],i=arguments.length>=2?arguments[1]:void 0,o=0;o>>0,i=0;if(2==arguments.length)n=arguments[1];else{for(;i=r)throw new TypeError("Reduce of empty array with no initial value");n=t[i++]}for(;i>>0;if(0===i)return-1;for(n=i-1,arguments.length>1&&(n=Number(arguments[1]),n!=n?n=0:0!==n&&n!=1/0&&n!=-1/0&&(n=(n>0||-1)*Math.floor(Math.abs(n)))),t=n>=0?Math.min(n,i-1):i-Math.abs(n);t>=0;t--)if(t in r&&r[t]===e)return t;return-1};t(Array.prototype,"lastIndexOf",c)}if(!Array.prototype.includes){var f=function(e){"use strict";if(null==this)throw new TypeError("Array.prototype.includes called on null or undefined");var n=Object(this),t=parseInt(n.length,10)||0;if(0===t)return!1;var r,i=parseInt(arguments[1],10)||0;i>=0?r=i:(r=t+i)<0&&(r=0);for(var o;r
In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.
The skateboard has a solid and stiff mini-deck, which is around 22 inches and constructed out of 100% plastic material. Such deck is very lightweight. It is only four pounds but you have an assurance that it can handle up to 198 lbs. of weight. You will also fall in love with the board as it comes in 23 graphics and colors, so picking a favorite is much easier.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air.[2] While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.[citation needed]
New Arrivals Men Backpacks & Bags Watches Wallets Sunglasses Hats Socks & Boxers Beanies Bandanas Belts Cologne Grooming Sun Care Jewelry Shoe Care SHOP ALL Women Backpacks Bags & Wallets Hats Belts Jewelry Sunglasses Watches Hair Accessories Socks & Tights Beauty SHOP ALL Phone & Tech Phone Accessories Tech Accessories Cameras Backpacks & Bags Backpacks Luggage & Duffle Bags Mini Backpacks Fanny Packs Lunch Bags Room & Home Kitchen & Drinkware Towels Inflatables Decor Pillows & Bedding Desk & School Supplies Novelties Stickers Patches Pins Keychains Air Fresheners Toys Toys & Plushes Blind Boxes Games Books Costumes & Masks Skateboards Longboard Skateboards Cruiser Skateboards Complete Skateboards Skate Accessories
The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.

Whatever you do, don’t give up. Keep trying. If what you’re doing isn’t working, try something new. Skateboarding is all about experimenting with new ideas and finding out what works. Keep tweaking your results until you get what you want. Watch as many trick tip videos as you can, get advice from good skaters, and remember to enjoy yourself. If you don’t give up and you keep trying, eventually you’ll master the Ollie. Don’t let it frustate you, it takes time and lots of practice.


Choosing a skateboard deck can be approached in a few different ways: you can choose your board based off the graphic, the brand, the shape, the width, or even the color. For most skateboarders, it’s a combination of all these factors, but if you’ve never skateboarded before, you may not know what shape, width, or brand you like best. In this case, choosing your favorite graphic would make total sense.
Unlike some deck options, which are completely bare, the Bamboo Skateboards Galaxy Series Cosmic Cloud Skateboard Deck features heat-stamped artwork on the underside of the board, including several geometric and interstellar designs, including a beautiful nebula. Bamboo Skateboards claims these boards last their customers three weeks longer than other decks. The company sells the boards in three sizes: 7.75-by-31.5-inches, 8-by-31.75-inches and 8.25-by-32-inches.

Bolted onto the underside of the tail end of a skateboard, the tail guard (also known as a "skid plate") protected the tail end from skid stops and other maneuvers that would otherwise wear away the wood (commonly known as razor tail) and decrease the longevity of the tail. Typically made of plastic, these were widely popular in the '80s but their usage quickly diminished with the arrival of two-tail board designs, which became increasingly popular in the '90s.


If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.
    Almost no one lands an ollie on their first try.  Repetition is the most important part of learning how to ollie.  Once you learn how to do an ollie, you can try doing them while rolling.  Learning is one of the funnest parts of skateboarding.  After you learn ollies, you can move onto 180s, Pop Shove-Its, and flips.  Soon a whole world of tricks will open up.
×