Finally, just roll away. If this sounds simple, then great – get out there and practice! If this sounds too complicated, don’t worry. Just go slow, and take your time. There is no time limit to learn how to ollie – some people learn in a day, and I know one guy that took over a year to learn how to ollie on his skateboard. Also, like with most things in skateboarding, your body is learning how to ollie more than your mind is. So, with practice, you’ll eventually get it.
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.

Before learning it, do have your riding basics down. Meaning you are very comfortable riding it around and doing kickturns and not be pushing mongo. Best to learn it whilst stationary with your wheels on a crack so that you don't move and slip out so much. I don't recommend doing it on grass or carpet cos when you pop the tail, it's gonna be absorbed by the floor and when you start doing it on pavement, your muscles will memorize a different way of doing it. So nope, no easy way out i guess.
The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
Bought for my 7yo's first real board, and for the price its perfect. Beginners look no further! Sure the trucks, bearings, and wheels are my choice, but as someone whose ridden for 20+ years, guarantee these items are way above Walmart status and are more than capable for you shred park or street. Bonus that it came no put together, can teach the little clone how to put it all together.
The Wonnv Retro Mini Cruiser 22 inch Complete Skateboard is 22″ Light Up Clear Banana Skateboard.  It is complete with Light Up Board, Wheels, Metal Trucks, ABEC-7 Bearings, and High-Quality Bushings.  The set also includes 6″ Metal Trucks, High-Speed ABEC-7 Bearings, High-Quality Bushings, and Hardware.  It has a unique Textured Waffle Pattern on Deck and designed for Maximum Grip.  The Deck measures about 22 x 6 x 4″.  It has a 6″ Truck Axle and 3″ Truck Hanger.  It requires 2 AAA Batteries and is recommended for skaters who are 6 years old and Up.  It has a 5 rating on Amazon.
In 1978, Alan Gelfand, who was given his nickname "Ollie" by Scott Goodman, learned to perform no-handed aerials in bowls and pools using a gentle raising of the nose and scooping motion to keep the board with the feet.[2][3] There are numerous references to Alan Gelfand's Ollie with most notably pictures in the 1970s skateboarding magazine "Skateboarder".
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.
The Rimable Complete 22″ Skateboard is the most compact street board that are ready-to-use.  It is best for exercise and fun, and very portable.  There are five colors that you can choose from Black, Blue, White, Purple, and Green.  It has high-quality construction, with a high-density plastic deck.  It features extremely smooth 59mm wheels along with ABEC7 bearings and solid aluminum trucks.  It measures 22″ long and 6″ wide and weighs 4 pounds.  It has the best rating of 4.3 on Amazon.
Any serious skateboarder will tell you that the ollie is the most fundamental skateboard trick. In fact, it's probably the first trick that you'll learn on your skateboard. They’re great for getting over obstacles, moving around on your board, or just looking cool. Know the right way to move your feet on the board and with a little bit of practice, you can learn to pull off the perfect ollie.
Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable
Im a girl too. And here’s the deal. Guys wont bring you down unless you make a big deal out of being a girl at a skatepark. Go to a skatepark, skate until you want to stop, rock it, and stay confident. Guys could not care less whether or not you’re a girl who skates, and thats the bottom line. You just gotta learn to ollie perfectly and you’ll get to the point where you’ll be making their confidence falter.
Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.

After that I went to my regular Olley spot to practice, fell so hard three times. My legs were so fucked up from the day before. Now I feel like shit because I had problem with a 20cm ledge I landed at least 100 times up and down yesterday. I’m even capable of 50cm ledges at slow speed, but I only get the front wheel and the board up so I have to put pressure on the nose to get it all the way up.
We’re assuming if you’re trying to learn how to do an ollie, you’re probably pretty new to skateboarding. You may already know whether you’re goofy or regular footed, but if not, try taking a quick hop onto your board with the intention of rolling forward (you might want to try on carpet first so you don’t slip backwards). If you’re left foot naturally ends up towards the front of your board, you’re regular-footed. If you ended up putting your right foot first, you’re goofy-footed.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
In this modern era, manufacturers are incorporating hi-tech processes and top-shelf materials into the construction of the skateboard. Companies such as Almost have several versions of hi-tech decks such as the Impact, Double Impact, and Uber Light Series. Element makes Highlight decks with inlayed fiberglass beams, and Foundation has its signature Fiberprime decks. Other manufactures such as Flip, Habitat, Plan B, Skate Mental, and Zero offer boards with high-end P2 Construction. Hi-tech decks differ from traditional 7-ply Maple in that they are inlayed with Carbon Fiber, Fiberglass, Poly Ply, or Kevlar to produce a stronger skateboard with more pop. For more options, head over to our stellar selection of Hi-Tech Decks! Although hi-tech decks have made a strong presence within the market, standard 7-ply Maple remain the gold standard. This is due to the solid feeling and pop afforded through layering 7 Maple wood veneers together. The large majority of skateboard decks offered are constructed of 7-ply Maple. Most board manufacturers offer both high-tech decks and standard 7-ply Maple. No matter what you desire, CCS offers a complete selection in multiple sizes, shapes, and construction types!
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!

The Krown Rookie Skateboard Complete 7.5 comes with thick, sturdy 7-ply maple wood deck. It gives you more control and permits you to perform various tricks. It features carbon steel ABEC-3 bearings, aluminum trucks, bushings and 54mm x 34mm wheels. This board is perfect for kids who are 8 years and older. It has a maximum weight capacity of up to 220 lbs.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain. 
×