Hi, I can do an Ollie for 1 month already but somehow my Ollie is always unbalanced, meaning the front nose pops much higher than the back wheel. I understand that this is due to my front foot not sliding up higher, but I’m not sure how to correct it because my foot seem to get stuck after sliding up about an inch. Is it because of wrong technique or lack of calf muscles?
Invented in the late 1970s by Alan "Ollie" Gelfand, the ollie has become a skateboarding fundamental, the basis for many other more complicated tricks. In its simplest form, the ollie is a jumping technique that allows skaters to hop over obstacles and onto curbs, etc. What's so amazing about the ollie is the way the skateboard seems to stick to the skater's feet in midair. Seeing pictures of skaters performing soaring 4-foot ollies, many people assume that the board is somehow attached to the skater's feet. It's not. What's even more amazing about the ollie is that to get the skateboard to jump up, the skater pushes down on the board! The secret to this paradoxical maneuver is rotation around multiple axes. Let's take a closer look.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
So you want to know how to ollie? Be warned, it’s not for the faint of heart, and a lot of people have tried and failed and tried some more and still failed and then eventually thrown their boards into a wall out of frustration (I have no idea who those people are). It’s by no means an easy skateboard trick, but if you want to know how to ollie, start with these simple tips:
There are other types of ollies that you can do either alongside or combine with the ones listed above, like the tailgrab, indy grab, melon grab, stalefish, tweak, and dolphin nose. All of those skateboard tricks are performed more or less how they sound, but you might want to watch some videos on youtube to see a pro in action (as well as awesome cat videos).
If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
We’re assuming if you’re trying to learn how to do an ollie, you’re probably pretty new to skateboarding. You may already know whether you’re goofy or regular footed, but if not, try taking a quick hop onto your board with the intention of rolling forward (you might want to try on carpet first so you don’t slip backwards). If you’re left foot naturally ends up towards the front of your board, you’re regular-footed. If you ended up putting your right foot first, you’re goofy-footed.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car. It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings. It is ready to use and you can easily store it in your backpack. It has an average rating of 4.5 on Amazon.
Do your Ollie, then, instantly after you pop your board, lift your back foot up to meet your front foot. That helped me solo much I improved twice in a few tries with using that trick. And, if that doesn’t help, it’s just a matter of practicing. If you practice a ly every day, you experiment, you will find u r solution. But, try lifting u r back foot high right after u pop 😉
It is mainly because those items are guaranteed to help you familiarize yourself with the ins and outs of using them. They are a big help in making you feel comfortable when you push off with your feet while also balancing on top of the board when riding. It is not good to go for a very technical product, so it’s best to choose the mentioned types first.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.