The fact that it has nice and attractive prints also makes it a fashion skateboard. You can use it to show not only your passion in the sport but also your fashion sense. It is also equipped with a high-density emery surface known for being both waterproof and non-slip. With that, you have a hundred percent assurance of your safety when you are riding on it.
The Wonnv Retro Mini Cruiser 22 inch Complete Skateboard is 22″ Light Up Clear Banana Skateboard.  It is complete with Light Up Board, Wheels, Metal Trucks, ABEC-7 Bearings, and High-Quality Bushings.  The set also includes 6″ Metal Trucks, High-Speed ABEC-7 Bearings, High-Quality Bushings, and Hardware.  It has a unique Textured Waffle Pattern on Deck and designed for Maximum Grip.  The Deck measures about 22 x 6 x 4″.  It has a 6″ Truck Axle and 3″ Truck Hanger.  It requires 2 AAA Batteries and is recommended for skaters who are 6 years old and Up.  It has a 5 rating on Amazon.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
My problem is Everytime I try to pop the back it’s not hard enough and I get no air. The article says to jump up so I do it physically and sometimes it seems to help. But when I watch skate videos and other skaters It doesn’t appear they are actually jumping up. They just seem to be popping the board. So should I physically jump? May sound stupid but it’s something I struggle with.
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
When learning it, you will, slip and fall. Feel like an idiot doing something over and over again and not getting it, feel fear bcos you don’t know what's going to happen to you once you pop the tail, jump and slide your foot and then you land. Will you land on your board, will you be on the pavement? Will you slip out, will u kick the board away, will you land primo? No one knows but you gotta try it out and find it out yourself. Whatever it is, don't give up cos it's the strength to persevere, be crazy persistent to achieve and most of all being patient in learning and progressing that let's you earn the skateboarder title for your ownself.

Level out on the way down – Before you start to head back towards the safety of the earth, level your feet out as the board begins to fall. If you’re trying to jump a gap on your board, this will help you keep going straight and maintain your momentum. Alternatively, you can land on your nose or tail and perform a manual out of the jump, but those are pretty advanced moves. Might want to wait until those little pink training wheels are off your board first.
Playwheels Disney Skateboard For Kids is a 21″ Wood single kicktail deck with painted edges.  It has clear sand spray top grip with color graphic and full-color bottom graphics with a retro shape.  It features multi-colored composite truck and baseplate components with carbon steel axles.  This is great for kids who are starting to learn skating.  It has an average rating of 4.2 on Amazon.
The skateboard has a solid and stiff mini-deck, which is around 22 inches and constructed out of 100% plastic material. Such deck is very lightweight. It is only four pounds but you have an assurance that it can handle up to 198 lbs. of weight. You will also fall in love with the board as it comes in 23 graphics and colors, so picking a favorite is much easier.
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.
My problem is that my board always lands crooked when I Ollie. The worst thing is that I even tell myself to “keep your shoulders straight” while I’m doing the Ollie and I still land crooked. I think it’s just hard for people to grasp the simple fact that everything on a skateboard has to be done horizontally which is odd because people don’t walk sideways. We walk straight. Like roller blading for example…. it’s easier for me to roller blade because I’m used to walking and running obviously except with a skateboard everything is as if you were hopping over a fence sideways. Skateboarding is tough.
Invented in the late 1970s by Alan "Ollie" Gelfand, the ollie has become a skateboarding fundamental, the basis for many other more complicated tricks. In its simplest form, the ollie is a jumping technique that allows skaters to hop over obstacles and onto curbs, etc. What's so amazing about the ollie is the way the skateboard seems to stick to the skater's feet in midair. Seeing pictures of skaters performing soaring 4-foot ollies, many people assume that the board is somehow attached to the skater's feet. It's not. What's even more amazing about the ollie is that to get the skateboard to jump up, the skater pushes down on the board! The secret to this paradoxical maneuver is rotation around multiple axes. Let's take a closer look.
    Almost no one lands an ollie on their first try.  Repetition is the most important part of learning how to ollie.  Once you learn how to do an ollie, you can try doing them while rolling.  Learning is one of the funnest parts of skateboarding.  After you learn ollies, you can move onto 180s, Pop Shove-Its, and flips.  Soon a whole world of tricks will open up.
As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!
In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.

The Powell Golden Dragon 2 Skateboard is an affordable and complete skateboard for the beginners and also for the advanced skaters.  It has high-rebound, hand-cast polyurethane wheels to give you a great roll and grip.  It measures 7.5 inches wide with a colorful screen-printed bottom.  It is made in China and has an average rating of 4.2 on Amazon.


LaderaSkateboards.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates. Additionally, LaderaSkateboards.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links. We do not specifically market to children under 13.


The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
×