If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
This ollie is commonly referred to as an “Ollie Nosebone.” First of all, you need good ollie skills. The key for this ollie is your front foot. When you reach the peak, (gently!) push your front foot forward not moving any other part of your body. That’s it, simple yet difficult. Of utmost importance is practicing your regular ollie over and over in various conditions so that extension tricks such as the ‘nosebone’ come almost naturally with experimentation. Nevertheless, here is a movie explaining how to do it.
You have all the time in the world to skate, but you don't have the time to build a skateboard yourself. Maybe it's just easier to get a complete skateboard than spend hours in the garage trying to screw on new trucks. Even though customization is awesome, it's not necessary. You just want the freedom of the ride. When you get your skateboard, you just want to be able to get out and ollie off the curb as fast as possible. Which is why Tillys has an awesome selection of complete skateboards for you. Choose from some of your favorite skateboard brands including Primitive and Element and more. The bottom graphics are probably the most important part, so you can definitely choose the one that best fits your style. Get your new complete skateboard right here.
When you’re searching for one of the best skateboard decks on the market, it’s important to not go overboard. You don’t need one that is made from the rarest wood or has the most unique design. The best boards may be the ones that balance cost, design and quality. Afterall, with healthy use, you’ll eventually have to replace your deck anyway. You want the one that will give you the most functionality and happiness while you use it.
A rushed take-off might be the problem here. Steps 2-4 of this trick tip could help you out. In order to make your feet “stick” to the board, you have to do the movement fluidly. But don’t stress yourself out! You should rather start with some preliminary exercises until you feel safe while ollieing. It is also important to pull your foot up to your board’s nose in a straight manner to prevent it from spinning.
As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.