My fiancee purchased this via my account and he says that it has good concave shape and pop.Assembling was fairly simple, easier if you have a box cutter on hand to help with laying the grip tape. The deck was the best part but the bearings were good too. He thought the bushings were the worst, after about two hours of skating, both bushings were crushed and stuck in one direction. He's been skating for almost 13 years. Hope this helps!
There are other types of ollies that you can do either alongside or combine with the ones listed above, like the tailgrab, indy grab, melon grab, stalefish, tweak, and dolphin nose. All of those skateboard tricks are performed more or less how they sound, but you might want to watch some videos on youtube to see a pro in action (as well as awesome cat videos).
Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.

The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
I just can get any height on my ollie at all! so frustrating!, i can pop the board nicely and get it off the ground like that, but then i try to slide my foot up the board and it just stays at that 45 degree angle from when i popped it, i just can’t seem to slide and get it horizontal in the air, or any height for that matter, i have watched countless ollie tips and tricks videos, and practised for hours on end, the same ollie, i can ride smoothly and fine, along the side-walk for example but i just cant get any grip to bring my board up and forward (i bought a new skateboard yesterday, and also new shoes) so its obviously me which is incompetent in completing this ollie! I know im kind of waffling on a bit, but i just can get the board to get any height! Please help if you can!

The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.
You can learn to ollie while standing stationary, or while your skateboard is rolling. Ollying while standing still works the same way as while rolling, but I think rolling ollies are easier than stationary ollies. If you would like to learn to ollie with your skateboard stationary, you can place your skateboard on some carpet or grass to keep it from rolling. If you prefer to learn to ollie while your skateboard is rolling, don’t go very fast at the start. Whichever way you learn to ollie, once you feel comfortable you should try to ollie the other way as well.

Low ollies: This can happen for a lot of reasons, but the biggest one is that you are not crouching low enough before your ollie, and not pulling your feet high enough after you jump. When you crouch down, try and touch the ground. When you jump, try to hit yourself in the chest with your knees. ​Both knees. Don’t worry about falling. That will happen sometimes – that’s just part of skateboarding! For more help, read the How Can I Make My Ollies Higher? FAQ
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.

Mounting hardware is a set of eight 10-32 UNF bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks (and any type of risers) to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard. Hardware is available in various lengths for mounting trucks with or without risers.
The Skatro Mini Cruiser Skateboard includes Abec 7 Skatro Bearings, 59MM Urethane Skatro wheels, and 3-inch lightweight aluminum trucks.  The Skatro Flexy Technology ensures optimal flex on every board. Skatro outperforms most of the leading brands and it has an amazing value.  You can take this board on the subway, plane, train, and even on the bus.  It includes a color matching T-tool.  It has the best rating of 4.8 on Amazon.
I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car.  It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings.  It is ready to use and you can easily store it in your backpack.  It has an average rating of 4.5 on Amazon.
×