This is how I learned how to ollie. Place your skateboard next to a curb, right up against it. This will help keep your board from rolling. Next, do everything that I just described, but don’t worry about what your board does. Just do it, and land up on top of the curb, on the sidewalk. Don’t stress about whether the skateboard will be there, or if you will get hurt – just go through the motions of ollying up the curb. If you do it right, the skateboard will be there. If you do it wrong, you’ll probably just land on your feet on the sidewalk. Here’s the key – just do it and expect it to work. Your body understands what you are trying to do, and the less you stress, the more it can kick in and fill in the blanks.
Jump – Ah yes, finally, we have reached the move itself. Basically, you have to do about twelve different things all at once to execute a successful ollie-pop: lift your front foot, press down with your back foot, angle your front ankle,  and jump. Lift the front foot off the ground first, and then move your back foot. This whole process is easier if you’re actually moving forward – since you don’t have to fight for balance – but it can be done while you’re standing still as well.
The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
Almost every skate shop will have a wall of boards that is either organized by brand, size, or alphabetically. At our CCS skate shop, we have multiple walls of boards that we try and keep ordered alphabetically. A wall of skateboards, at first glance, can be overwhelming, but if you know what size and roughly what brands you like, it should be fairly easy for you to figure out what board you want. Now would be a good time to mention our CCS Skateboard Buyer’s Guide, specifically the Decks Guide. In the CCS Decks Guide, you’ll find all the information you need to gain a basic understanding of skateboard decks.

The Bamboo Mini Cruiser deck is 6-inches-by-22.5-inches with that classic cruiser shape. The board is made with 6-ply bamboo and maple construction, which is lightweight, flexible and eco-friendly. Bamboo Skateboards claims this board has a turning radius not seen in most mini decks. The small, blank deck is heavy duty and durable in a way not all mini cruisers are. The non-carbonized board is ready for you to slap on the grip tape and artwork you want and then get riding.


The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
I have been doing ollie’s for about a year to a year and a halve, but thats not the problem. My problem is the board turns when i ollie, i cant help it, i am starting to go into harder ground (ollying off ledges and ollying stairs) but i cant land and ride away because my board has turned in a 45 degree angle and it jerks me off the board, Please help in all you can, cheers mate.
The wheels are also impressive. Unlike some other skateboards that have wheels that are quite stiff, causing them to feel like they will lock up when you ride on them, the wheels in this complete skateboard for beginners are smooth and comfortable. These are also easily controllable, so rest assured that they offer a smooth and friction-free glide.
Popsicle - A Popsicle complete skateboard is typically between 30 and 34 inches in total length with a varying width between 6.0 inches wide and 9.25 inches wide. You can check out the deck size chart to pick the complete that will be best suitable for you. These decks all come with grip tape and are a more technical skateboard for tricks and for the skatepark. If you want to do more than cruise the streets, a Popsicle is what you are looking for. All of our complete skateboards include the deck, trucks, wheels, grip, bearings and hardware. They are all also fully assembled. When choosing a complete, typically the more expensive completes will include a higher quality deck, better and longer lasting trucks, upgraded wheels and a higher abec rating on the bearings.
New Arrivals Clothing Dresses & Rompers Tops Sweaters Sweatshirts & Hoodies Jackets Jeans Pants Leggings Shorts Skirts Swim Intimates Bras Panties Bodysuits Intimate Accessories Shoes Sneakers Boots & Booties Sandals Flats Heels & Wedges Slippers Accessories Backpacks Bags & Wallets Hats & Beanies Jewelry Hair Accessories Sunglasses Socks Belts Watches Scarves Hydro Flask Beauty Hair Bath & Body Makeup Fragrance Sun Care Brushes & Tools Deals RSQ Jeans BOGO 50% Off Sweaters BOGO 50% Off Sweatshirts BOGO 50% Off Tops 4 for $25 Tees 2 for $20 Backpacks 30-50% Off Panties 5 for $16 Bralettes BOGO 50% Off Vogue Sunglasses 40% Off Sunglasses 50% Off Jewelry BOGO 50% Off Sunglasses 2 for $15 Trends COZY SHOP Riverdale Zipper Details Corduroy Color Trends Menswear Florals Stripes Checkered Button Front Tie Front Tie Dye & Crystal Wash Disney X Vans Converse X Hello Kitty Levi's X Mickey Only at Tillys
As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.

The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life.
Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
Ancheer 31″ Pro Skateboards are made of 7-ply maple wood and finished with anti-slip grip tape.  It includes 60mm PU wheels ideal for riders who want to carve out sections, obtain speed and higher off the ground for tricks. It features 6″ Tony Hawk Signature aluminum trucks and 32″ long deck with double kick tail which is ideal for perfecting your favorite tricks.  It comes with ABEC-7 skateboard bearings.  It has style and quality which is expected from the most influential skateboarders of all time.  It is one of the best-rated skateboards on Amazon with a rating of 4.8.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
When learning it, you will, slip and fall. Feel like an idiot doing something over and over again and not getting it, feel fear bcos you don’t know what's going to happen to you once you pop the tail, jump and slide your foot and then you land. Will you land on your board, will you be on the pavement? Will you slip out, will u kick the board away, will you land primo? No one knows but you gotta try it out and find it out yourself. Whatever it is, don't give up cos it's the strength to persevere, be crazy persistent to achieve and most of all being patient in learning and progressing that let's you earn the skateboarder title for your ownself.
Whatever you do, don’t give up. Keep trying. If what you’re doing isn’t working, try something new. Skateboarding is all about experimenting with new ideas and finding out what works. Keep tweaking your results until you get what you want. Watch as many trick tip videos as you can, get advice from good skaters, and remember to enjoy yourself. If you don’t give up and you keep trying, eventually you’ll master the Ollie. Don’t let it frustate you, it takes time and lots of practice.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
Skateboarding is all about creativity and finding new challenges. A great way to explore skateboarding is to ride different shaped boards, wider trucks, and different size wheels. As you progress and start to ride new terrain and skate different kinds of spots, you may find one wheel size or board shape works better for you than another. There’s no wrong or right anything. There are no rules. Except for maybe one, and that is to keep skating. Skate as often as you can. Never is this more true than in the beginning while you’re developing your style and fundamentals.

A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.
So the proper foot placement for the ollie is with the ball of your back foot horizontal on the tail of your skateboard.  And your front foot centered on your board right behind the front trucks.  You may find that moving your feet around in different positions are more comfortable.  This is fine,  everybody can learn how to skateboard their own way.
Pop in your earbuds and head to the skate park with a skateboard that rolls through impressive stunts with ease. Most skateboards for sale offer strong wood decks that create a stable feel beneath your feet as you work on your grind and backslide techniques, but models with polypropylene construction offer a lightweight alternative with plenty of toughness. Try a surfboard-inspired design to cruise the streets like you'd ride a wave, or select a drop-through deck for smooth cruising. Grip tape promotes sure footing that helps you ride with confidence, but always put safety first - wear a skate helmet and skate pads from our Skateboard Shop for protection against mid-move falls.

The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!
Skateboard hardware is used to connect the skateboard trucks to the skateboard deck. Skateboard hardware refers to the bolts and locknuts used when building a board. The bolts can have an Allen or Phillips head. Skateboard hardware comes in many different lengths, and often includes one different colored bolt so that the rider can mark the nose of their board.
Pop in your earbuds and head to the skate park with a skateboard that rolls through impressive stunts with ease. Most skateboards for sale offer strong wood decks that create a stable feel beneath your feet as you work on your grind and backslide techniques, but models with polypropylene construction offer a lightweight alternative with plenty of toughness. Try a surfboard-inspired design to cruise the streets like you'd ride a wave, or select a drop-through deck for smooth cruising. Grip tape promotes sure footing that helps you ride with confidence, but always put safety first - wear a skate helmet and skate pads from our Skateboard Shop for protection against mid-move falls.
A skateboard deck is made up of curved layers of wood that are combined with glue. Then, the skateboard deck is trimmed down to a board shape that is practical. Trucks are typically made of aluminum or other metal alloys. They are made by melted metal formed by a mold and later drilled into the skateboard deck. The wheels are formed the same way, but with polyurethane. They are attached by ball bearings to complete the product.
This is how I learned how to ollie. Place your skateboard next to a curb, right up against it. This will help keep your board from rolling. Next, do everything that I just described, but don’t worry about what your board does. Just do it, and land up on top of the curb, on the sidewalk. Don’t stress about whether the skateboard will be there, or if you will get hurt – just go through the motions of ollying up the curb. If you do it right, the skateboard will be there. If you do it wrong, you’ll probably just land on your feet on the sidewalk. Here’s the key – just do it and expect it to work. Your body understands what you are trying to do, and the less you stress, the more it can kick in and fill in the blanks.
×