Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
Large power is created at the point of action by applying small power to the point of effort. Application of this concept to skateboarding makes the back wheels the fulcrum, the tail the point of effort, and the nose the point of action. Applying power to the tail causes the nose to shoot upwards. When the front foot of the skater levels the nose at a point roughly horizontal to the ground in anticipation of the tail, soon to be leveled likewise by the skater’s back foot, the process smoothly done creates the illusion of the skateboard ‘sticking’ to the feet.

The laws for skateboarding helmets vary from state to state. Many states require that skaters wear a helmet under a certain age, and some states like California make all skaters under 18 wear a CPSC Certified helmet at all times. CSPC skateboard helmets usually have an EPS protective liner that meets the safety standards for skateboarding. Make sure you check your state's regulations before ordering.


Whatever you do, don’t give up. Keep trying. If what you’re doing isn’t working, try something new. Skateboarding is all about experimenting with new ideas and finding out what works. Keep tweaking your results until you get what you want. Watch as many trick tip videos as you can, get advice from good skaters, and remember to enjoy yourself. If you don’t give up and you keep trying, eventually you’ll master the Ollie. Don’t let it frustate you, it takes time and lots of practice.

Invented in the late 1970s by Alan "Ollie" Gelfand, the ollie has become a skateboarding fundamental, the basis for many other more complicated tricks. In its simplest form, the ollie is a jumping technique that allows skaters to hop over obstacles and onto curbs, etc. What's so amazing about the ollie is the way the skateboard seems to stick to the skater's feet in midair. Seeing pictures of skaters performing soaring 4-foot ollies, many people assume that the board is somehow attached to the skater's feet. It's not. What's even more amazing about the ollie is that to get the skateboard to jump up, the skater pushes down on the board! The secret to this paradoxical maneuver is rotation around multiple axes. Let's take a closer look.

If you are looking to buy a pre-built complete for yourself or someone else, CCS has pre-built complete skateboards for sale, too. This is by far the fastest way to buy a skateboard complete and often times the least expensive. Because we work directly with the manufacturer's, the cheapest skateboard complete for sale is our CCS Logo Skateboard Complete.
So now that you have an idea of what size and shape board you like, it’s time to choose a brand. A popular size is an 8.5 skateboard deck. If you were looking for a size 8.5 skateboard deck, you could narrow the decks offered on CCS.com to fit in the 8.25 - 8.5 range. This will show you all the boards in that range, and significantly reduce the boards you have to look through. Now, if you don’t have a preference on board brands, find a graphic you like and you’re all set. If this is your first skateboard or are still learning about what wood and brands you prefer, we recommend checking out a CCS Skateboard. They give you a bang for your buck, that's for sure.
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!

Are you on a hunt for the best skateboard on the market today? Then you are in the right place as this comprehensive article is designed to give you information about skateboarding and types of skateboards in general. By learning about the different types of skateboards and what each one can do, figuring out what works for you the best is a lot easier.
The Bamboo Skateboards Galaxy Series Cosmic Cloud Skateboard Deck is an excellent option. This concave board is made exclusively of a bamboo hybrid, rather than pure maple. This means the deck is lighter, stronger, more flexible and can even absorb shock better. The non-carbonized, light-wood deck is made of 6-ply wood and is in its fourth generation of designs.
When you’re searching for one of the best skateboard decks on the market, it’s important to not go overboard. You don’t need one that is made from the rarest wood or has the most unique design. The best boards may be the ones that balance cost, design and quality. Afterall, with healthy use, you’ll eventually have to replace your deck anyway. You want the one that will give you the most functionality and happiness while you use it.
The switch stance ollie uses a similar body motion, but the nollie is subtly distinct: For one, the rider is always moving forward, with the body positioned in a nollie stance--closer to the nose and with the front foot on the nose. Secondly the rider usually postures the body differently so as to compensate for this stance with respect to the forward motion. The rider presses the nose down using their front foot to engage the "pop" motion in order for the board to rise. This is In contrast to a "Fakie Ollie" where the pop motion is performed by the rear foot on the tail, similarly to a normal Ollie, however the rider is traveling backwards when performing a Fakie Ollie. Where in a Nollie the rider is traveling forward with their front foot on the nose to apply the initial force "pop".

Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
A rushed take-off might be the problem here. Steps 2-4 of this trick tip could help you out. In order to make your feet “stick” to the board, you have to do the movement fluidly. But don’t stress yourself out! You should rather start with some preliminary exercises until you feel safe while ollieing. It is also important to pull your foot up to your board’s nose in a straight manner to prevent it from spinning.
Skateboards can be bought online and in your local stores.  However, choosing a good skateboard can be challenging.  If you are a beginner there are a lot of things that you have to consider.  Aside from the cost, you should also check the entire board such as the wheels, the deck, the trucks, and others.  Here, we have compiled the best skateboards for sale that you can choose from right now.

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
×