The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
The longboard, a common variant of the skateboard, is used for higher speed and rough surface boarding, and they are much more expensive. "Old school" boards (those made in the 1970s–80s or modern boards that mimic their shape) are generally wider and often have only one kicktail. Variants of the 1970s often have little or no concavity, whereas 1980s models have deeper concavities and steeper kicktails.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
New Arrivals Clothing T-Shirts Shirts Sweatshirts & Hoodies Jackets Sweaters Jeans Pants Joggers & Sweatpants Shorts Boardshorts Tank Tops Shoes Sneakers Boots Sandals Slippers Shoe Care Accessories Backpacks & Bags Watches Wallets Sunglasses Hats Beanies Socks Boxers Belts Skateboards Grooming Cologne Sun Care Jewelry Stickers Hydro Flask Deals Graphic Tees 2 for $30 RSQ Jeans BOGO 50% Off Joggers BOGO 50% Off Levi's $48.99 Flannels $24.99 Sweatshirts BOGO 50% Off Tees BOGO 50% Off Backpacks 30-50% Off Collections Brixton x Coors adidas x Beavis and Butthead Diamond Supply Co. x Family Guy Disney x Vans Nixon x Disney HUF x Peanuts Primitive x Rick and Morty Vans x Marvel adidas Watches Americana Asian Inspired Street Athletic Roses Tropical Prints Camo Stripes Tie Dye Checkerboard Party Prints College Tees Rick & Morty NASA Only at Tillys
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot. This is the ‘pop’. It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work. Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
Jump – Ah yes, finally, we have reached the move itself. Basically, you have to do about twelve different things all at once to execute a successful ollie-pop: lift your front foot, press down with your back foot, angle your front ankle, and jump. Lift the front foot off the ground first, and then move your back foot. This whole process is easier if you’re actually moving forward – since you don’t have to fight for balance – but it can be done while you’re standing still as well.
The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car. It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings. It is ready to use and you can easily store it in your backpack. It has an average rating of 4.5 on Amazon.