Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.
Velocity Boards Retro Banana Skateboard is a 22″ Complete Board Set with 6″ Aluminum Trucks, ABEC-7 Bearings, High-Quality Wheels, and Bushings. It is designed for maximum grip. The Deck measures about 22 x 6 x 4″. The truck Axle has a Width of 6″ and the Truck Hanger has a Width of 3″. It has a maximum load capacity of 176 lbs. (80 kgs.) It is best for skaters who are 6 years old and Up. It has an average Amazon rating of 4.7.

So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
Bolted onto the underside of the tail end of a skateboard, the tail guard (also known as a "skid plate") protected the tail end from skid stops and other maneuvers that would otherwise wear away the wood (commonly known as razor tail) and decrease the longevity of the tail. Typically made of plastic, these were widely popular in the '80s but their usage quickly diminished with the arrival of two-tail board designs, which became increasingly popular in the '90s.
I have skated for about 7 years i took a 2 year break. I have had about 50 boards and from that id say this board is ok seeing as iv had zero's break day one. if your newer to skateboarding and you dont mind the cost i would say go for it. For more hardcore skaters there are some things you should know about this board. im not 100% about the trucks day one just doing kickflips 360 flips smaller gaps.. its a bit shaky i dont think these trucks are make for stairs or big gaps but they will do till i have the cash for some thunders. the bearings are hit or miss one is on its way to being blow out the others seem to be fine. I got to say i really like the wheels there was not much info on them but they are smaller and harder and i love harder wheels i hit a nice nolie 360 first try and the sound of the slide took me back to the good days. As for the board i cant judge it off one day of skating but from the looks of it its not a knock off. Here are some tips for buying a board online. find real skaters in the comments dont buy a board because a dad said his kid loves it. When you get the board go over all the parts and look over your board well make sure there are no defects in the board. make sure the board is not waterlogged a few taps should tell you. if you dont know anything about skateboards ask a friend to help and if you find any defects send it back right away. I hope the review helps you.

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Plan B sells boards with overall reliable attributes. They offer decks made from seven-ply wood. Powell is a longstanding company that founded the legendary Bones Brigade team, which kick-started Tony Hawk's career. Their skateboard designs change annually, but always look cool. Tony Hawk’s skate company is called Birdhouse. Their decks feature bird themes and have a thicker sixth layer of wood that makes it easier to jump and do flip tricks, which is ideal for vertical-style skateboarding. For environmentally-conscious skaters and fans of Bam Margera, buy a board from Element. They have variety on the technical side with their seven-ply boards and Helium decks. Their skateboards are made with an air pocket to be lightweight.
Skateboard hardware is used to connect the skateboard trucks to the skateboard deck. Skateboard hardware refers to the bolts and locknuts used when building a board. The bolts can have an Allen or Phillips head. Skateboard hardware comes in many different lengths, and often includes one different colored bolt so that the rider can mark the nose of their board.

This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
×