If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air.[2] While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.[citation needed]

The Element Quadrant #14 board is 8-inches wide and 31.75-inches long, from nose to tail. This deck features a bare top that needs grip tape and a design on the bottom with four quadrants featuring the Element symbol in alternating red and black backgrounds. The wheelbase between the trucks is just over 14 inches while the nose is 7 inches and the tail is 6.325. 


Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.

Here we have an original Z Jimmy Plumer model. It has some handling scuffing from being around for several decades, but displays great. Grip has no holes at trucks which leads me to believe it’s never had any mounted. This is one heavy fiberglass mamma jamma. Get this piece of history at a fair price. I will throw in free priority insured shipping for the con us. Everywhere else at actual cost. Thanks for looking.


Popsicle - A Popsicle complete skateboard is typically between 30 and 34 inches in total length with a varying width between 6.0 inches wide and 9.25 inches wide. You can check out the deck size chart to pick the complete that will be best suitable for you. These decks all come with grip tape and are a more technical skateboard for tricks and for the skatepark. If you want to do more than cruise the streets, a Popsicle is what you are looking for. All of our complete skateboards include the deck, trucks, wheels, grip, bearings and hardware. They are all also fully assembled. When choosing a complete, typically the more expensive completes will include a higher quality deck, better and longer lasting trucks, upgraded wheels and a higher abec rating on the bearings.
    Almost no one lands an ollie on their first try.  Repetition is the most important part of learning how to ollie.  Once you learn how to do an ollie, you can try doing them while rolling.  Learning is one of the funnest parts of skateboarding.  After you learn ollies, you can move onto 180s, Pop Shove-Its, and flips.  Soon a whole world of tricks will open up.
The Skatro Mini Cruiser Skateboard includes Abec 7 Skatro Bearings, 59MM Urethane Skatro wheels, and 3-inch lightweight aluminum trucks.  The Skatro Flexy Technology ensures optimal flex on every board. Skatro outperforms most of the leading brands and it has an amazing value.  You can take this board on the subway, plane, train, and even on the bus.  It includes a color matching T-tool.  It has the best rating of 4.8 on Amazon.
Choosing a skateboard deck is a great place to start when building a complete skateboard. Unless you have experience riding a shaped board - something a little more retro or unusual, we recommend you start with a popsicle shape. CCS carries over 60 different skateboard deck brands that sell this popular popsicle shape. If you have questions on what size you should ride or have any other questions about building a complete, we recommend you check out our Skateboard Buyer’s Guide. Here, you’ll find helpful how-to’s for choosing a skateboard decks, skateboard trucks, skateboard wheels, skateboard bearings, and skateboard components. This guide explains every part of a skateboard and helps you choose which sizes and styles to best suit your needs.
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.

The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
Skateboard hardware is used to connect the skateboard trucks to the skateboard deck. Skateboard hardware refers to the bolts and locknuts used when building a board. The bolts can have an Allen or Phillips head. Skateboard hardware comes in many different lengths, and often includes one different colored bolt so that the rider can mark the nose of their board.
Skateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems,How to ollie on a skateboard,how to ollie on a skateboard,how to ollie higher,how to ollie while moving,how to ollie on a skateboard for beginners,how to ollie while moving for beginners,how to ollie stairs,skateboarding tricks,skateboarding ollie tutorial,skateboarding ollie slow motion,how to ollie up a curb,how to ollie while moving,overindulgingSkateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems
This board includes professional assembly. All Krown skateboards arrived assembled and ready to ride straight out the box. The Rookie model includes heavy duty Aluminum 5.0 trucks, 52mm 99A high-rebound urethane wheels, precision speed Abec 7 bearings, high tensile phillips head mounting hardware, and 80 grit black grip tape. Each component meets the industry standards and are a common choice of skaters worldwide.
The Rimable Complete 22″ Skateboard is the most compact street board that are ready-to-use.  It is best for exercise and fun, and very portable.  There are five colors that you can choose from Black, Blue, White, Purple, and Green.  It has high-quality construction, with a high-density plastic deck.  It features extremely smooth 59mm wheels along with ABEC7 bearings and solid aluminum trucks.  It measures 22″ long and 6″ wide and weighs 4 pounds.  It has the best rating of 4.3 on Amazon.
An Ollie is basically an upward/forward jumping trick. The name “ollie” comes from the nickname of Alan Gelfand who created the ollie in 1976. The ollie was then modified for flat-ground use by Rodney Mullen in 1982, and it is this flat-ground version of the ollie which is most commonly referred to as the ‘ollie’ today. The ollie is arguably the most important trick in skateboarding because it is the foundation of the majority of skateboard tricks which require lift. When you want to do a trick like the kickflip, when you want to get onto something like a ledge, or down something like a set of stairs, or try handrails, the ability to ollie is a necessity. Therefore the ability to ollie high and with good control is critical to your total skateboarding skill-set.
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve 
×