The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Almost is proud to announce a collaboration with Skateistan, the award-winning non-profit organization empowering children and youth through skateboarding and education. They recently launched a new Skate School in Phnom Penh, Cambodia on Friday (February 23rd, 2018). Over 100 children celebrated alongside special guests from around the world, including Almost flow skater Sky Brown. 
The Wonnv Retro Mini Cruiser 22 inch Complete Skateboard is 22″ Light Up Clear Banana Skateboard.  It is complete with Light Up Board, Wheels, Metal Trucks, ABEC-7 Bearings, and High-Quality Bushings.  The set also includes 6″ Metal Trucks, High-Speed ABEC-7 Bearings, High-Quality Bushings, and Hardware.  It has a unique Textured Waffle Pattern on Deck and designed for Maximum Grip.  The Deck measures about 22 x 6 x 4″.  It has a 6″ Truck Axle and 3″ Truck Hanger.  It requires 2 AAA Batteries and is recommended for skaters who are 6 years old and Up.  It has a 5 rating on Amazon.
When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.

Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
The most important thing when you learn to skateboard is to skate with people that are at a higher skill lv than you, then they can tell you what you are doin wrong. Its so **cing anoing when you skate alle alone, wondering why your board is turning, and you haw to go to the internet to find out that it is something so easy as ceeping your shoulders straight.
With Enkeeo 22 Inch Cruiser Skateboards, you can cruise in style.  It has a dimension of 22 x 6 inches.  It comes with 3″ Black Coated Habitat trucks, Black 60mm Smooth wheels, and Abec11 bearings. It’s ready to ride and you can even personalize the tail of the board for free with a limitation of 10 Characters only. It has 30 days warranty and is manufactured in California.  It has a perfect 5 rating on Amazon.
A complete skateboard is pre-assembled - it almost rides right out of the package and on to the streets, ready for you to practice all your new tricks. You simply don’t have to think about buying the separate parts like trucks, wheels, decks or the likes. Once you have gained more experience on the board and you feel like customizing it to fit your skateboarding style, you can begin to learn more about the different pieces in order to assemble a skateboard that meets your specific wishes and demands. Until then, a complete can be quite the right choice.
This ollie is commonly referred to as an “Ollie Nosebone.” First of all, you need good ollie skills. The key for this ollie is your front foot. When you reach the peak, (gently!) push your front foot forward not moving any other part of your body. That’s it, simple yet difficult. Of utmost importance is practicing your regular ollie over and over in various conditions so that extension tricks such as the ‘nosebone’ come almost naturally with experimentation. Nevertheless, here is a movie explaining how to do it.
Slide your front foot as soon as you start jumping. Use the same movement you have been practicing to slide your foot towards the top end of the board, just as you jump off it and kick the back down. The front of your board should lift up as you slide your foot along it, with your foot hitting the top of the board at the highest point of your jump.[9]
Im a girl too. And here’s the deal. Guys wont bring you down unless you make a big deal out of being a girl at a skatepark. Go to a skatepark, skate until you want to stop, rock it, and stay confident. Guys could not care less whether or not you’re a girl who skates, and thats the bottom line. You just gotta learn to ollie perfectly and you’ll get to the point where you’ll be making their confidence falter.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
Hey guys. I’m a girl and I am having some trouble with my ollie. I know the steps in order to do an ollie, but I can’t seem to do all of them. I can do a perfect pop on the back foot, but my problem lies in my front foot. (I am regular footed but idk if that matters) I know I just need to get my back wheels off the ground, but when I try to slide it, my foot just stays frozen. I try really hard to make it move, and when it does it just goes straight across, skimming the bottom of my shoes. Even then I can only move it half an inch. I have pretty mild griptape, that might change something? Idk.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.

It wouldn’t be until the early 1980’s however, that a man named Rodney Mullen fully developed the skateboard ollie and brought it into vogue. Competing in the Rusty Harris contest in Whittier, California in 1982, Rodney Mullen used a back and forth motion on his skateboard to strike the back end of the board on the ground and using the front end to level the board out in mid-air – all from a flat surface. The audience’s jaws collectively hit the ground.


The Krown Rookie Skateboard Complete 7.5 comes with thick, sturdy 7-ply maple wood deck. It gives you more control and permits you to perform various tricks. It features carbon steel ABEC-3 bearings, aluminum trucks, bushings and 54mm x 34mm wheels. This board is perfect for kids who are 8 years and older. It has a maximum weight capacity of up to 220 lbs.
No I don’t believe that. You have to feel your board with your toes and feel the shape that the board Under the bottom of your feet and then master the pop with this newly formed connection. Faster faster and more guts are needed. When you are going as fast as you can go and can Ollie perfectly with complete consistency you’ll Ollie everywhere even in the cold cold winter.
You have all the time in the world to skate, but you don't have the time to build a skateboard yourself. Maybe it's just easier to get a complete skateboard than spend hours in the garage trying to screw on new trucks. Even though customization is awesome, it's not necessary. You just want the freedom of the ride. When you get your skateboard, you just want to be able to get out and ollie off the curb as fast as possible. Which is why Tillys has an awesome selection of complete skateboards for you. Choose from some of your favorite skateboard brands including Primitive and Element and more. The bottom graphics are probably the most important part, so you can definitely choose the one that best fits your style. Get your new complete skateboard right here.
Regardless of your skill level, you definitely need quality skateboard parts and that begins with skateboard trucks. We carry hundreds of top-selling skate trucks! Hardcore skateboarders love our Independent skate trucks for their performance and durability. You can also pick out the perfect skateboard wheels, like a blazing fast set of Spitfires, and you'll be one step closer to skating like a pro. To make the most of your skate wheels, you'll need quality skate bearings, too—check out top-seller Bones Bearings. When building a skateboard, even the smallest choices make a difference, so be sure to get the right size skate hardware, double-check your skateboard bushings, and don't forget to grit up your board with grip tape.
It is a mini-cruiser, which is known for its strength as well as its ability to offer real value for the money you spent. This skateboard can also be expected to deliver an impressive performance – thanks to the Abec 7 skatro bearings used in it. There are also 59-mm urethane wheels and the 3-inch GOLD aluminum trucks that can help smoothen each ride.

The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.

Finally, just roll away. If this sounds simple, then great – get out there and practice! If this sounds too complicated, don’t worry. Just go slow, and take your time. There is no time limit to learn how to ollie – some people learn in a day, and I know one guy that took over a year to learn how to ollie on his skateboard. Also, like with most things in skateboarding, your body is learning how to ollie more than your mind is. So, with practice, you’ll eventually get it.

×