Bolted onto the underside of the tail end of a skateboard, the tail guard (also known as a "skid plate") protected the tail end from skid stops and other maneuvers that would otherwise wear away the wood (commonly known as razor tail) and decrease the longevity of the tail. Typically made of plastic, these were widely popular in the '80s but their usage quickly diminished with the arrival of two-tail board designs, which became increasingly popular in the '90s.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

The skater can gain greater clearance from the ground by jumping higher, popping faster, sliding the front foot farther forwards (starting the jump with the front foot farther back), and pulling the legs higher into the chest to raise the feet higher. Skaters attempting record-setting ollies even contort the legs so that board and feet are not directly below them, allowing the board to rise at or just below the level of the pelvis.
Skateboarding started in California in the 1950s.[2] The first skateboards were made from roller skates (attached to a board).[3] Skateboarding gained in popularity because of surfing; in fact, skateboarding was initially referred to as "sidewalk surfing". Initially, skateboards were handmade from wooden boxes and planks by individuals. As the sport became more popular, companies started manufacturing skateboards. Boards are also continuing to evolve as companies try to make them lighter and stronger or improve their performance.
Slide your front foot as soon as you start jumping. Use the same movement you have been practicing to slide your foot towards the top end of the board, just as you jump off it and kick the back down. The front of your board should lift up as you slide your foot along it, with your foot hitting the top of the board at the highest point of your jump.[9]
Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.  
If you’ve ever watched a skateboarder roll down the street and then all of a sudden pop into the air on a skateboard, you’re probably wondering the same question a lot of people do: how on earth do they do that? It almost seems magical how they just seem to explode off the ground, and then just kind of float. Skateboarder, meet, the ollie. It’s not in the category of “easy skateboard tricks,” but if you learn how to ollie, you’re well on your way to fame and fortune as a professional skater.
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
If you’ve ever watched a skateboarder roll down the street and then all of a sudden pop into the air on a skateboard, you’re probably wondering the same question a lot of people do: how on earth do they do that? It almost seems magical how they just seem to explode off the ground, and then just kind of float. Skateboarder, meet, the ollie. It’s not in the category of “easy skateboard tricks,” but if you learn how to ollie, you’re well on your way to fame and fortune as a professional skater.
The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
×