The board also boasts of its reasonably small size and lightweight nature, making it easy to control and ride. In addition, carrying it wherever you want to go is also much easier because of its lightness. It is flexible enough that it can accommodate the needs of different kinds of users, including cruisers, travelers, beginners, expert riders, and kids.
Are you on a hunt for the best skateboard on the market today? Then you are in the right place as this comprehensive article is designed to give you information about skateboarding and types of skateboards in general. By learning about the different types of skateboards and what each one can do, figuring out what works for you the best is a lot easier.

Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.


The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
Hey guys. I’m a girl and I am having some trouble with my ollie. I know the steps in order to do an ollie, but I can’t seem to do all of them. I can do a perfect pop on the back foot, but my problem lies in my front foot. (I am regular footed but idk if that matters) I know I just need to get my back wheels off the ground, but when I try to slide it, my foot just stays frozen. I try really hard to make it move, and when it does it just goes straight across, skimming the bottom of my shoes. Even then I can only move it half an inch. I have pretty mild griptape, that might change something? Idk.
After you’ve properly applied a burst of force to the tail, the top-side of your front foot’s toe should start dragging up your board almost automatically. Eventually, the higher you are able to bring your front foot during lift will determine the apex of your ollie, so work gradually towards lifting your front foot as high as your body allows. Skateboarders who record the highest ollies usually (somehow manage to!) bring their feet higher than their hips!
This was a simple purchase. No issues at all and the skateboards are really nice! Some people have said it comes unassembled, that's not the case. I ordered 2 different boards and both came assembled and ready to roll.. The boards are topped with grip tape and trucks and wheels were assembled perfectly. If I had a need to get another board I would run straight back to this kit, they are great!
Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.

If you’ve ever watched a skateboarder roll down the street and then all of a sudden pop into the air on a skateboard, you’re probably wondering the same question a lot of people do: how on earth do they do that? It almost seems magical how they just seem to explode off the ground, and then just kind of float. Skateboarder, meet, the ollie. It’s not in the category of “easy skateboard tricks,” but if you learn how to ollie, you’re well on your way to fame and fortune as a professional skater.


The most important thing when you learn to skateboard is to skate with people that are at a higher skill lv than you, then they can tell you what you are doin wrong. Its so **cing anoing when you skate alle alone, wondering why your board is turning, and you haw to go to the internet to find out that it is something so easy as ceeping your shoulders straight.
As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
Sublimation (phase transition) is the transition of a substance directly from the solid to the gas phase without passing through an intermediate liquid phase. Sublimation is an endothermic phase transition that occurs at temperatures and pressures below a substance's triple point in its phase diagram. In this case, ink is transferred to a base layer, fibreglass for example, through heat and pressure, the result is a full color graphic that will not come off as easily as the more common heat transfers. This application is often found with bamboo boards and composite construction longboards where fibreglass can allow for various degrees of flex or stiffness depending on the ride you're looking for, cruising and carving versus slalom and downhill.

It is a mini-cruiser, which is known for its strength as well as its ability to offer real value for the money you spent. This skateboard can also be expected to deliver an impressive performance – thanks to the Abec 7 skatro bearings used in it. There are also 59-mm urethane wheels and the 3-inch GOLD aluminum trucks that can help smoothen each ride.


The DreadXBoards Concave Skateboard has Plastic Deck Injection Molded for excellent durability. It features Urethane Wheels 59mm 78a, aluminum trucks, and Abec 7 Bearings. It is completely assembled and is ready to ride. It is perfect for beginners or experienced riders. It can load up to 185 lbs. It is great for kids and adults. It has an excellent rating of 4 on Amazon.
Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.

This ollie is commonly referred to as an “Ollie Nosebone.” First of all, you need good ollie skills. The key for this ollie is your front foot. When you reach the peak, (gently!) push your front foot forward not moving any other part of your body. That’s it, simple yet difficult. Of utmost importance is practicing your regular ollie over and over in various conditions so that extension tricks such as the ‘nosebone’ come almost naturally with experimentation. Nevertheless, here is a movie explaining how to do it.
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
×