As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
Ridge Skateboards For Beginners are a UK Brand and have taken over Europe. Now it is available in the U.S.A. exclusively through Amazon. The Deck measures 27″ long x 7.5″ wide (69cm x 19cm). It features 4″ wide high-performance trucks with 87A super soft yellow bushings. It is made of high quality secret plastic formula. It has a rating of 4.8 on Amazon.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).

I found that my problem was unclear instruction about the timing between jumping and popping. One day when I was watching a slowmo ollie video though, I noticed that the skateboarder already was beginning to jump (at least his body was already going in an upward motion) before snapping the board off the ground. That was a critical change I needed to make in order to get it working. I had been trying to pop the board while all my weight was still pushing down on it (kind of an obvious mistake, but I somehow overlooked this). Hope this helps somebody.


This is how I learned how to ollie. Place your skateboard next to a curb, right up against it. This will help keep your board from rolling. Next, do everything that I just described, but don’t worry about what your board does. Just do it, and land up on top of the curb, on the sidewalk. Don’t stress about whether the skateboard will be there, or if you will get hurt – just go through the motions of ollying up the curb. If you do it right, the skateboard will be there. If you do it wrong, you’ll probably just land on your feet on the sidewalk. Here’s the key – just do it and expect it to work. Your body understands what you are trying to do, and the less you stress, the more it can kick in and fill in the blanks.
You can learn to ollie while standing stationary, or while your skateboard is rolling. Ollying while standing still works the same way as while rolling, but I think rolling ollies are easier than stationary ollies. If you would like to learn to ollie with your skateboard stationary, you can place your skateboard on some carpet or grass to keep it from rolling. If you prefer to learn to ollie while your skateboard is rolling, don’t go very fast at the start. Whichever way you learn to ollie, once you feel comfortable you should try to ollie the other way as well.
My son seems to have a lot of fun riding this skateboard. He will be out there doing tricks for hours. One evening when he took a break, I decided to see if I could still ride. When I took off down the driveway, I could feel how smoothly the wheels rolled. I used to have to pay extra for wheels like this when I was his age. Lost in thought, I coasted faster, and my neighbour didn't see me when I shot out of the driveway. Even though this thing flew several feet in the air, bounced, and came to rest more than 20 feet away, it had no visible damage! Not so for me. I loved the skateboard, but am now recovering from two broken ribs, torn neck cartilage, and a cracked pelvis. Still, this board rides like a dream!

In 1978, Alan Gelfand, who was given his nickname "Ollie" by Scott Goodman, learned to perform no-handed aerials in bowls and pools using a gentle raising of the nose and scooping motion to keep the board with the feet.[2][3] There are numerous references to Alan Gelfand's Ollie with most notably pictures in the 1970s skateboarding magazine "Skateboarder".


EXPERIENCED SKATER! This board is amazing for the price! (notice i said FOR THE PRICE) At the time of this review, the board was $44.40 and for that price the board i got was phenomenal. It is a 7-ply deck with aluminum trucks (havent figured out the bearings but they definitely feel like the abec 5 they claim to be). The trucks arent the best quality out there and the board can be a little thinner (maybe 5-ply) but the overall board is amazing. There are only two complaints. The hole in the wheels is a tiny TINY TIIINYYY bit off center, but nothing that cant be fixed with a new set. I can see what another review said by it not coming assembled, as a couple of the bolts on the wheels are a little loose, but the board does come assembled.
I’ve been skating for about 3-4 years, I can kickflip, pop shuv it, front shuv, 180 and almost heelflips. I can ollie and used to be very good at them and could get them clean, but when I started practicing kickflips, it made my slide all weird. I can still ollie ( though it’s not as clean) but now when I ollie I slide with my pinky toe and that region, instead of the side of my foot. How can I fix my slide? When I try practicing sliding with the side of my foot, it doesnt feel like I can turn my foot that far towards the board and when I do it slowly to see what im doing, i still slide with my toes.Thank you.
A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.

When learning it, you will, slip and fall. Feel like an idiot doing something over and over again and not getting it, feel fear bcos you don’t know what's going to happen to you once you pop the tail, jump and slide your foot and then you land. Will you land on your board, will you be on the pavement? Will you slip out, will u kick the board away, will you land primo? No one knows but you gotta try it out and find it out yourself. Whatever it is, don't give up cos it's the strength to persevere, be crazy persistent to achieve and most of all being patient in learning and progressing that let's you earn the skateboarder title for your ownself.
Here we have an original Z Jimmy Plumer model. It has some handling scuffing from being around for several decades, but displays great. Grip has no holes at trucks which leads me to believe it’s never had any mounted. This is one heavy fiberglass mamma jamma. Get this piece of history at a fair price. I will throw in free priority insured shipping for the con us. Everywhere else at actual cost. Thanks for looking.
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
Ridge Skateboards For Beginners are a UK Brand and have taken over Europe. Now it is available in the U.S.A. exclusively through Amazon. The Deck measures 27″ long x 7.5″ wide (69cm x 19cm). It features 4″ wide high-performance trucks with 87A super soft yellow bushings. It is made of high quality secret plastic formula. It has a rating of 4.8 on Amazon.
Do your Ollie, then, instantly after you pop your board, lift your back foot up to meet your front foot. That helped me solo much I improved twice in a few tries with using that trick. And, if that doesn’t help, it’s just a matter of practicing. If you practice a ly every day, you experiment, you will find u r solution. But, try lifting u r back foot high right after u pop 😉

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.


Regardless of your skating ability or style, CCS is the definitive place for the best skateboard decks around. With hundreds in stock, take your pick from some of the sickest decks available! Alien Workshop, Baker, Deathwish, Element, enjoi, Girl, Welcome. WKND, Santa Cruz, Primitive, and Real are among the most popular offered. Additionally, notable brands such as Almost, DGK, Flip, Krooked, Alien Workshop, Skate Mental, Zero, Creature, and Chocolate are available for all your skating needs.
The most important thing when you learn to skateboard is to skate with people that are at a higher skill lv than you, then they can tell you what you are doin wrong. Its so **cing anoing when you skate alle alone, wondering why your board is turning, and you haw to go to the internet to find out that it is something so easy as ceeping your shoulders straight.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.

The Rimable Complete 22″ Skateboard is the most compact street board that are ready-to-use.  It is best for exercise and fun, and very portable.  There are five colors that you can choose from Black, Blue, White, Purple, and Green.  It has high-quality construction, with a high-density plastic deck.  It features extremely smooth 59mm wheels along with ABEC7 bearings and solid aluminum trucks.  It measures 22″ long and 6″ wide and weighs 4 pounds.  It has the best rating of 4.3 on Amazon.
If you are looking to buy a pre-built complete for yourself or someone else, CCS has pre-built complete skateboards for sale, too. This is by far the fastest way to buy a skateboard complete and often times the least expensive. Because we work directly with the manufacturer's, the cheapest skateboard complete for sale is our CCS Logo Skateboard Complete.
In most cases, it is available in black but you can also find clear ones that are ideal for you if you want to show a specific logo. Another nice choice that you have is the die-cut grip tape, which works in displaying the color or design of the deck beneath it. Make sure to choose a grip tape at a size, which perfectly suits your skateboard’s deck.
New Arrivals Clothing Dresses & Rompers Tops Sweaters Sweatshirts & Hoodies Jackets Jeans Pants Leggings Shorts Skirts Swim Intimates Bras Panties Bodysuits Intimate Accessories Shoes Sneakers Boots & Booties Sandals Flats Heels & Wedges Slippers Accessories Backpacks Bags & Wallets Hats & Beanies Jewelry Hair Accessories Sunglasses Socks Belts Watches Scarves Hydro Flask Beauty Hair Bath & Body Makeup Fragrance Sun Care Brushes & Tools Deals RSQ Jeans BOGO 50% Off Sweaters BOGO 50% Off Sweatshirts BOGO 50% Off Tops 4 for $25 Tees 2 for $20 Backpacks 30-50% Off Panties 5 for $16 Bralettes BOGO 50% Off Vogue Sunglasses 40% Off Sunglasses 50% Off Jewelry BOGO 50% Off Sunglasses 2 for $15 Trends COZY SHOP Riverdale Zipper Details Corduroy Color Trends Menswear Florals Stripes Checkered Button Front Tie Front Tie Dye & Crystal Wash Disney X Vans Converse X Hello Kitty Levi's X Mickey Only at Tillys
Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.[5]
×