The Skatro Mini Cruiser Skateboard includes Abec 7 Skatro Bearings, 59MM Urethane Skatro wheels, and 3-inch lightweight aluminum trucks.  The Skatro Flexy Technology ensures optimal flex on every board. Skatro outperforms most of the leading brands and it has an amazing value.  You can take this board on the subway, plane, train, and even on the bus.  It includes a color matching T-tool.  It has the best rating of 4.8 on Amazon.
Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie
An Ollie is basically an upward/forward jumping trick. The name “ollie” comes from the nickname of Alan Gelfand who created the ollie in 1976. The ollie was then modified for flat-ground use by Rodney Mullen in 1982, and it is this flat-ground version of the ollie which is most commonly referred to as the ‘ollie’ today. The ollie is arguably the most important trick in skateboarding because it is the foundation of the majority of skateboard tricks which require lift. When you want to do a trick like the kickflip, when you want to get onto something like a ledge, or down something like a set of stairs, or try handrails, the ability to ollie is a necessity. Therefore the ability to ollie high and with good control is critical to your total skateboarding skill-set.
beginner skateboarder beginner skateboarders beginner skateboarder tips beginner skateboarding tricks common ollie mistakes get better at skateboarding get more pop how to kickflip how to ollie how to skateboard improve at skateboarding kickflip kickflip trick tip landing tricks consistently learn how to ollie learn how to skateboard ollie higher overcoming fear popping tricks higher pop shuvit pop tricks higher secrets of skateboarding skateboarding skateboarding chickenfoot skateboarding secrets skateboarding tips skateboarding tricks skateboarding trick tips skateboard tricks skateboard tricks for beginners skateboard trick tips skatepark skatepark tips style matters skateboarding tricks for beginners trick tips trips for beginner skateboarders
Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.

The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.


Hey guys. I’m a girl and I am having some trouble with my ollie. I know the steps in order to do an ollie, but I can’t seem to do all of them. I can do a perfect pop on the back foot, but my problem lies in my front foot. (I am regular footed but idk if that matters) I know I just need to get my back wheels off the ground, but when I try to slide it, my foot just stays frozen. I try really hard to make it move, and when it does it just goes straight across, skimming the bottom of my shoes. Even then I can only move it half an inch. I have pretty mild griptape, that might change something? Idk.
The Quest Super Cruiser is made of Canadian Maple and measures 31″(787mm)x8″(203mm). It has a maximum capacity of 500 lbs. The wheels have a size of 1.99″(50mm)x1.42″(36mm) Pu with logo printing. The pattern is heat transferred. The trucks are 5″ heavy duty aluminum alloy. This skateboard can provide you a high-quality ride with an entry-level price. This is the best skateboard for both beginners and price-conscious expert skaters. It has an average rating of 4.3 on Amazon.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

The fact that it has nice and attractive prints also makes it a fashion skateboard. You can use it to show not only your passion in the sport but also your fashion sense. It is also equipped with a high-density emery surface known for being both waterproof and non-slip. With that, you have a hundred percent assurance of your safety when you are riding on it.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.

Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.


If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
Shock pads are made of polyurethane and rubber. They are very similar to risers but vary in the fact that their sole purpose is to cushion the board from the trucks. Since the trucks are metal and the board wood, whenever the board hits the ground after doing a trick, the energy goes through the truck to the board ─ this has caused boards to crack, split, or even break in half, and shock pads were created to prevent this.
Cheap Hoverboard Drones Drones with Camera Electric Scooter Electric Skateboard Freeboard Gifts for Skateboarders GoPro Alternative Cameras Headphones Hoverboard Laws How to Ride a Snakeboard Longboard Longboards Mini Segway Mopeds Mopeds for Sale Quadcopters Quadcopters with Camera Ripstick Rollerblades Roller Skates Self Balancing Board Self Balancing Scooter Self Balancing Unicycle Skate 3 Skateboard Skateboard Backpacks skateboard d Skateboard Decks Skateboard Girls Skateboarding Tricks Skateboard Quotes Skateboard Rack Skateboards Skateboard Trucks Skatecycles Skate Game Skate Logos Skate Shoes Ski Jackets Smart Electric Scooter Snakeboard Unicycle Scooter Vans Waveboards
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
×