I just can get any height on my ollie at all! so frustrating!, i can pop the board nicely and get it off the ground like that, but then i try to slide my foot up the board and it just stays at that 45 degree angle from when i popped it, i just can’t seem to slide and get it horizontal in the air, or any height for that matter, i have watched countless ollie tips and tricks videos, and practised for hours on end, the same ollie, i can ride smoothly and fine, along the side-walk for example but i just cant get any grip to bring my board up and forward (i bought a new skateboard yesterday, and also new shoes) so its obviously me which is incompetent in completing this ollie! I know im kind of waffling on a bit, but i just can get the board to get any height! Please help if you can!
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

Crouch down – While you’re standing on the board with your feet in the right position, crouch down closer towards the board. Don’t turn into a hunchback here; keep your back as straight as possible and don’t stick your rear out too far off the board, otherwise you’ll mess the whole thing up. Stay on the balls of your feet too; if you’re more on your toes, you’ll actually move the board in air and land off of it, and no one wants that. If you need to readjust your feet before you jump, just do a little micro-jump to reposition your feet, or shuffle into position. The first way is easier and faster, the second is more awkward and can mess up your shoes.
!function(n,t){function r(e,n){return Object.prototype.hasOwnProperty.call(e,n)}function i(e){return void 0===e}if(n){var o={},s=n.TraceKit,a=[].slice,l="?";o.noConflict=function(){return n.TraceKit=s,o},o.wrap=function(e){function n(){try{return e.apply(this,arguments)}catch(e){throw o.report(e),e}}return n},o.report=function(){function e(e){l(),h.push(e)}function t(e){for(var n=h.length-1;n>=0;--n)h[n]===e&&h.splice(n,1)}function i(e,n){var t=null;if(!n||o.collectWindowErrors){for(var i in h)if(r(h,i))try{h[i].apply(null,[e].concat(a.call(arguments,2)))}catch(e){t=e}if(t)throw t}}function s(e,n,t,r,s){var a=null;if(w)o.computeStackTrace.augmentStackTraceWithInitialElement(w,n,t,e),u();else if(s)a=o.computeStackTrace(s),i(a,!0);else{var l={url:n,line:t,column:r};l.func=o.computeStackTrace.guessFunctionName(l.url,l.line),l.context=o.computeStackTrace.gatherContext(l.url,l.line),a={mode:"onerror",message:e,stack:[l]},i(a,!0)}return!!f&&f.apply(this,arguments)}function l(){!0!==d&&(f=n.onerror,n.onerror=s,d=!0)}function u(){var e=w,n=p;p=null,w=null,m=null,i.apply(null,[e,!1].concat(n))}function c(e){if(w){if(m===e)return;u()}var t=o.computeStackTrace(e);throw w=t,m=e,p=a.call(arguments,1),n.setTimeout(function(){m===e&&u()},t.incomplete?2e3:0),e}var f,d,h=[],p=null,m=null,w=null;return c.subscribe=e,c.unsubscribe=t,c}(),o.computeStackTrace=function(){function e(e){if(!o.remoteFetching)return"";try{var t=function(){try{return new n.XMLHttpRequest}catch(e){return new n.ActiveXObject("Microsoft.XMLHTTP")}},r=t();return r.open("GET",e,!1),r.send(""),r.responseText}catch(e){return""}}function t(t){if("string"!=typeof t)return[];if(!r(j,t)){var i="",o="";try{o=n.document.domain}catch(e){}var s=/(.*)\:\/\/([^:\/]+)([:\d]*)\/{0,1}([\s\S]*)/.exec(t);s&&s[2]===o&&(i=e(t)),j[t]=i?i.split("\n"):[]}return j[t]}function s(e,n){var r,o=/function ([^(]*)\(([^)]*)\)/,s=/['"]?([0-9A-Za-z$_]+)['"]?\s*[:=]\s*(function|eval|new Function)/,a="",u=10,c=t(e);if(!c.length)return l;for(var f=0;f0?s:null}function u(e){return e.replace(/[\-\[\]{}()*+?.,\\\^$|#]/g,"\\$&")}function c(e){return u(e).replace("<","(?:<|<)").replace(">","(?:>|>)").replace("&","(?:&|&)").replace('"','(?:"|")').replace(/\s+/g,"\\s+")}function f(e,n){for(var r,i,o=0,s=n.length;or&&(i=s.exec(o[r]))?i.index:null}function h(e){if(!i(n&&n.document)){for(var t,r,o,s,a=[n.location.href],l=n.document.getElementsByTagName("script"),d=""+e,h=/^function(?:\s+([\w$]+))?\s*\(([\w\s,]*)\)\s*\{\s*(\S[\s\S]*\S)\s*\}\s*$/,p=/^function on([\w$]+)\s*\(event\)\s*\{\s*(\S[\s\S]*\S)\s*\}\s*$/,m=0;m]+)>|([^\)]+))\((.*)\))? in (.*):\s*$/i,o=n.split("\n"),l=[],u=0;u=0&&(g.line=v+x.substring(0,j).split("\n").length)}}}else if(o=d.exec(i[y])){var _=n.location.href.replace(/#.*$/,""),T=new RegExp(c(i[y+1])),E=f(T,[_]);g={url:_,func:"",args:[],line:E?E.line:o[1],column:null}}if(g){g.func||(g.func=s(g.url,g.line));var k=a(g.url,g.line),A=k?k[Math.floor(k.length/2)]:null;k&&A.replace(/^\s*/,"")===i[y+1].replace(/^\s*/,"")?g.context=k:g.context=[i[y+1]],h.push(g)}}return h.length?{mode:"multiline",name:e.name,message:i[0],stack:h}:null}function y(e,n,t,r){var i={url:n,line:t};if(i.url&&i.line){e.incomplete=!1,i.func||(i.func=s(i.url,i.line)),i.context||(i.context=a(i.url,i.line));var o=/ '([^']+)' /.exec(r);if(o&&(i.column=d(o[1],i.url,i.line)),e.stack.length>0&&e.stack[0].url===i.url){if(e.stack[0].line===i.line)return!1;if(!e.stack[0].line&&e.stack[0].func===i.func)return e.stack[0].line=i.line,e.stack[0].context=i.context,!1}return e.stack.unshift(i),e.partial=!0,!0}return e.incomplete=!0,!1}function g(e,n){for(var t,r,i,a=/function\s+([_$a-zA-Z\xA0-\uFFFF][_$a-zA-Z0-9\xA0-\uFFFF]*)?\s*\(/i,u=[],c={},f=!1,p=g.caller;p&&!f;p=p.caller)if(p!==v&&p!==o.report){if(r={url:null,func:l,args:[],line:null,column:null},p.name?r.func=p.name:(t=a.exec(p.toString()))&&(r.func=t[1]),"undefined"==typeof r.func)try{r.func=t.input.substring(0,t.input.indexOf("{"))}catch(e){}if(i=h(p)){r.url=i.url,r.line=i.line,r.func===l&&(r.func=s(r.url,r.line));var m=/ '([^']+)' /.exec(e.message||e.description);m&&(r.column=d(m[1],i.url,i.line))}c[""+p]?f=!0:c[""+p]=!0,u.push(r)}n&&u.splice(0,n);var w={mode:"callers",name:e.name,message:e.message,stack:u};return y(w,e.sourceURL||e.fileName,e.line||e.lineNumber,e.message||e.description),w}function v(e,n){var t=null;n=null==n?0:+n;try{if(t=m(e))return t}catch(e){if(x)throw e}try{if(t=p(e))return t}catch(e){if(x)throw e}try{if(t=w(e))return t}catch(e){if(x)throw e}try{if(t=g(e,n+1))return t}catch(e){if(x)throw e}return{mode:"failed"}}function b(e){e=1+(null==e?0:+e);try{throw new Error}catch(n){return v(n,e+1)}}var x=!1,j={};return v.augmentStackTraceWithInitialElement=y,v.guessFunctionName=s,v.gatherContext=a,v.ofCaller=b,v.getSource=t,v}(),o.extendToAsynchronousCallbacks=function(){var e=function(e){var t=n[e];n[e]=function(){var e=a.call(arguments),n=e[0];return"function"==typeof n&&(e[0]=o.wrap(n)),t.apply?t.apply(this,e):t(e[0],e[1])}};e("setTimeout"),e("setInterval")},o.remoteFetching||(o.remoteFetching=!0),o.collectWindowErrors||(o.collectWindowErrors=!0),(!o.linesOfContext||o.linesOfContext<1)&&(o.linesOfContext=11),void 0!==e&&e.exports&&n.module!==e?e.exports=o:"function"==typeof define&&define.amd?define("TraceKit",[],o):n.TraceKit=o}}("undefined"!=typeof window?window:global)},"./webpack-loaders/expose-loader/index.js?require!./shared/require-global.js":function(e,n,t){(function(n){e.exports=n.require=t("./shared/require-global.js")}).call(n,t("../../../lib/node_modules/webpack/buildin/global.js"))}});
This was a simple purchase. No issues at all and the skateboards are really nice! Some people have said it comes unassembled, that's not the case. I ordered 2 different boards and both came assembled and ready to roll.. The boards are topped with grip tape and trucks and wheels were assembled perfectly. If I had a need to get another board I would run straight back to this kit, they are great!
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.
You can learn to ollie while standing stationary, or while your skateboard is rolling. Ollying while standing still works the same way as while rolling, but I think rolling ollies are easier than stationary ollies. If you would like to learn to ollie with your skateboard stationary, you can place your skateboard on some carpet or grass to keep it from rolling. If you prefer to learn to ollie while your skateboard is rolling, don’t go very fast at the start. Whichever way you learn to ollie, once you feel comfortable you should try to ollie the other way as well.
Maybe you're new to skateboarding. We have lots of complete skateboards or longboards to get you started. All of our skateboard and longboard completes come fully assembled, so you can hit the streets without any of the hassle—try an Enjoi skateboard complete or check out our selection of Sector 9 longboard and skateboard completes. Or maybe you're an experienced skater looking to update and customize your ride. You probably want to start with the perfect skateboard deck before you do anything else. We carry high-quality skate decks to keep you steady and balanced while you bomb, slide, and carve the streets. We also have a variety of longboard decks in stock if you're looking for a smooth ride for cruising or commuting.
Penny Skateboards make premium plastic skateboards, letting you chase the sunshine and good times. Available in a great range of colours, including pastels, brights and prints, there’s sure to be a Penny Skateboard to match your unique style. Prefer to customise your ride? Head to the hardware store to update your griptape and wheels, making your Penny look brand new! Embrace the Penny lifestyle, join in the fun and find your favourite Penny products for sale online.

James Haden is one of the owners of the Skateboarder community, together with Nash Gibson – his co-owner. He works as a full-time copywriter for a private company and also a true adventurer. He is an avid reader, writer, traveler, and extreme sports junkie. During his free time, he researches interesting content for their blog and continuously writes for their audience.
Are you on a hunt for the best skateboard on the market today? Then you are in the right place as this comprehensive article is designed to give you information about skateboarding and types of skateboards in general. By learning about the different types of skateboards and what each one can do, figuring out what works for you the best is a lot easier.
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
LaderaSkateboards.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates. Additionally, LaderaSkateboards.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links. We do not specifically market to children under 13.
500AlmostAluminatiArborBambooBirdhouseBlindBonzingCometCreatureDarkstarDB LongboardsDevilleDogtownDusters CaliforniaElementEnjoiEverseshFlipFocusFoundationGlobeGoldCoastGravityHabitatJartKebbekKrookedLandyachtzLaybackLushMadridMakahaMoonshine MFGOmenPennyPlan BPowell PeraltaPrism SkatePunkedRayneRealRememberRivieraRoad RiderSan ClementeSanta CruzSector 9Suicidal SkatesToy MachineWarehouseZ-FlexZero
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!

In fact, we can work out how you need to steer the skateboard. Tracker has a nice feature that we'll call 'force arrows'. These arrows show you how much force acts on an object at every instant, and in which direction the force acts. So for example, if you were to kick a ball into the air, while the ball was mid-flight, this arrow would always point down and be the same length, even though the ball is moving forward. That's because the only force acting on the ball is gravity, which pulls it straight down, and acts with a constant strength. (For those of you who've studied physics, these arrows denote the acceleration of the center of mass, which by Newton's second law is proportional to the net force acting on the skateboard.)
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air.[2] While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.[citation needed]

Velocity Boards Retro Banana Skateboard is a 22″ Complete Board Set with 6″ Aluminum Trucks, ABEC-7 Bearings, High-Quality Wheels, and Bushings. It is designed for maximum grip. The Deck measures about 22 x 6 x 4″. The truck Axle has a Width of 6″ and the Truck Hanger has a Width of 3″. It has a maximum load capacity of 176 lbs. (80 kgs.) It is best for skaters who are 6 years old and Up. It has an average Amazon rating of 4.7.
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
Skateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems,How to ollie on a skateboard,how to ollie on a skateboard,how to ollie higher,how to ollie while moving,how to ollie on a skateboard for beginners,how to ollie while moving for beginners,how to ollie stairs,skateboarding tricks,skateboarding ollie tutorial,skateboarding ollie slow motion,how to ollie up a curb,how to ollie while moving,overindulgingSkateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems
Bought as a Christmas gift for our nephew. He's not an expert or anything so I was looking for something that would work while he gets used to riding one. When I received it I pulled it out of the package to check it out and the construction was good. The wheels spun smoothly and the grip tape was nicely put on. I don't know how it would resist to some board slides but for a 15 year old just starting out its a good board.
One foot on the tail, (by foot I mean the ball of the foot which is just behind the big toe) the other foot is about an inch behind the bolts(screws) for the front truck. Basically, the back foot quickly pushes the tail down, and right when the tail of the board strikes the ground, the back foot jumps up… the tail of the board will follow up with the foot when the front foot slides forward slightly, which pivots the tail of the board upwards. Since the front truck comes off the ground first, getting the back truck up is the trick.
Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.
This ollie is commonly referred to as an “Ollie Nosebone.” First of all, you need good ollie skills. The key for this ollie is your front foot. When you reach the peak, (gently!) push your front foot forward not moving any other part of your body. That’s it, simple yet difficult. Of utmost importance is practicing your regular ollie over and over in various conditions so that extension tricks such as the ‘nosebone’ come almost naturally with experimentation. Nevertheless, here is a movie explaining how to do it.
The board also boasts of its reasonably small size and lightweight nature, making it easy to control and ride. In addition, carrying it wherever you want to go is also much easier because of its lightness. It is flexible enough that it can accommodate the needs of different kinds of users, including cruisers, travelers, beginners, expert riders, and kids.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
Do your Ollie, then, instantly after you pop your board, lift your back foot up to meet your front foot. That helped me solo much I improved twice in a few tries with using that trick. And, if that doesn’t help, it’s just a matter of practicing. If you practice a ly every day, you experiment, you will find u r solution. But, try lifting u r back foot high right after u pop 😉

I just can get any height on my ollie at all! so frustrating!, i can pop the board nicely and get it off the ground like that, but then i try to slide my foot up the board and it just stays at that 45 degree angle from when i popped it, i just can’t seem to slide and get it horizontal in the air, or any height for that matter, i have watched countless ollie tips and tricks videos, and practised for hours on end, the same ollie, i can ride smoothly and fine, along the side-walk for example but i just cant get any grip to bring my board up and forward (i bought a new skateboard yesterday, and also new shoes) so its obviously me which is incompetent in completing this ollie! I know im kind of waffling on a bit, but i just can get the board to get any height! Please help if you can!


If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
It's a neat piece of science art, and it also tells us something interesting. The arrows show us that the force on the skateboard is constantly changing, both in magnitude as well as in direction. Now the force of gravity obviously isn't changing, so the reason that these force arrows are shrinking and growing and tumbling around is that the skater is changing how their feet pushes and pulls against the board. By applying a variable force that changes both in strength and direction, they're steering the board.
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.
Cruiser - The name says it all. If you are looking to cruise around town then this is the right complete skateboard for you. These decks vary in length from between 20 inches all the way up to about 40 inches. The wheel diameters usually start at about 55 millimeters and use a much softer urethane than the previous Popsicle decks. These also come with all of the above but the decks do not always need grip tape. Some of the decks are plastic or composite material with grooves or gripping built directly into the deck mold. 
This board includes professional assembly. All Krown skateboards arrived assembled and ready to ride straight out the box. The Rookie model includes heavy duty Aluminum 5.0 trucks, 52mm 99A high-rebound urethane wheels, precision speed Abec 7 bearings, high tensile phillips head mounting hardware, and 80 grit black grip tape. Each component meets the industry standards and are a common choice of skaters worldwide.
So now that you have an idea of what size and shape board you like, it’s time to choose a brand. A popular size is an 8.5 skateboard deck. If you were looking for a size 8.5 skateboard deck, you could narrow the decks offered on CCS.com to fit in the 8.25 - 8.5 range. This will show you all the boards in that range, and significantly reduce the boards you have to look through. Now, if you don’t have a preference on board brands, find a graphic you like and you’re all set. If this is your first skateboard or are still learning about what wood and brands you prefer, we recommend checking out a CCS Skateboard. They give you a bang for your buck, that's for sure.
In fact, we can work out how you need to steer the skateboard. Tracker has a nice feature that we'll call 'force arrows'. These arrows show you how much force acts on an object at every instant, and in which direction the force acts. So for example, if you were to kick a ball into the air, while the ball was mid-flight, this arrow would always point down and be the same length, even though the ball is moving forward. That's because the only force acting on the ball is gravity, which pulls it straight down, and acts with a constant strength. (For those of you who've studied physics, these arrows denote the acceleration of the center of mass, which by Newton's second law is proportional to the net force acting on the skateboard.)

In this modern era, manufacturers are incorporating hi-tech processes and top-shelf materials into the construction of the skateboard. Companies such as Almost have several versions of hi-tech decks such as the Impact, Double Impact, and Uber Light Series. Element makes Highlight decks with inlayed fiberglass beams, and Foundation has its signature Fiberprime decks. Other manufactures such as Flip, Habitat, Plan B, Skate Mental, and Zero offer boards with high-end P2 Construction. Hi-tech decks differ from traditional 7-ply Maple in that they are inlayed with Carbon Fiber, Fiberglass, Poly Ply, or Kevlar to produce a stronger skateboard with more pop. For more options, head over to our stellar selection of Hi-Tech Decks! Although hi-tech decks have made a strong presence within the market, standard 7-ply Maple remain the gold standard. This is due to the solid feeling and pop afforded through layering 7 Maple wood veneers together. The large majority of skateboard decks offered are constructed of 7-ply Maple. Most board manufacturers offer both high-tech decks and standard 7-ply Maple. No matter what you desire, CCS offers a complete selection in multiple sizes, shapes, and construction types!
James Haden is one of the owners of the Skateboarder community, together with Nash Gibson – his co-owner. He works as a full-time copywriter for a private company and also a true adventurer. He is an avid reader, writer, traveler, and extreme sports junkie. During his free time, he researches interesting content for their blog and continuously writes for their audience.
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.

My problem is that my board always lands crooked when I Ollie. The worst thing is that I even tell myself to “keep your shoulders straight” while I’m doing the Ollie and I still land crooked. I think it’s just hard for people to grasp the simple fact that everything on a skateboard has to be done horizontally which is odd because people don’t walk sideways. We walk straight. Like roller blading for example…. it’s easier for me to roller blade because I’m used to walking and running obviously except with a skateboard everything is as if you were hopping over a fence sideways. Skateboarding is tough.
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.
×