The laws for skateboarding helmets vary from state to state. Many states require that skaters wear a helmet under a certain age, and some states like California make all skaters under 18 wear a CPSC Certified helmet at all times. CSPC skateboard helmets usually have an EPS protective liner that meets the safety standards for skateboarding. Make sure you check your state's regulations before ordering.
A skateboard consists of a deck, trucks, wheels, bearings, hardware, and griptape. All parts come in a variety of sizes, graphics, colors, and signature pro series. The deck is the essential part of any skateboard. The deck ranges generally from 7.5" to 8.5". Skaters choose their board size for many reasons, but the basic deciding factor comes down to style of skating and foot size. Transition skaters usually ride a wider deck, while street skaters tend to go with a smaller deck. Skate brands such as Girl, enjoi, and Welcome offer a wide range of boards in regards to sizes and graphics. Skateboard trucks come in either a high or low setting, and also in a range of widths. The main factors in a truck, are how well they turn, and how well they grind. Independent, Venture, and Thunder, are truck brands that are well known for their turning and grinding capabilities. The skate hardware is generally either Phillips head or Allen key bolts. The skateboard wheels range from 50mm to 60mm. Some brands offer smaller and larger sizes, but 50-60mm is the general range. Like the deck sizes, wheel sizes depend on the skater's choice of terrain: Transition skaters tend to ride bigger wheels, while street skaters usually go with smaller wheels. Bones, Spitfire, Ricta, and Wayward wheel companies all make wheels for any terrain, whether you're a street shredder or a park burner. Skate bearings follow the ABEC rating system, which includes grades 1, 3, 5, 7, and 9. Bones, Bronson, and Andale are some of the top bearing brands in the skate market. CCS proudly carries all these brands, and many more.
LaderaSkateboards.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon, the Amazon logo, AmazonSupply, and the AmazonSupply logo are trademarks of Amazon.com, Inc. or its affiliates. Additionally, LaderaSkateboards.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links. We do not specifically market to children under 13.
Shock pads are made of polyurethane and rubber. They are very similar to risers but vary in the fact that their sole purpose is to cushion the board from the trucks. Since the trucks are metal and the board wood, whenever the board hits the ground after doing a trick, the energy goes through the truck to the board ─ this has caused boards to crack, split, or even break in half, and shock pads were created to prevent this.
Jump – Ah yes, finally, we have reached the move itself. Basically, you have to do about twelve different things all at once to execute a successful ollie-pop: lift your front foot, press down with your back foot, angle your front ankle, and jump. Lift the front foot off the ground first, and then move your back foot. This whole process is easier if you’re actually moving forward – since you don’t have to fight for balance – but it can be done while you’re standing still as well.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Regardless of your skating ability or style, CCS is the definitive place for the best skateboard decks around. With hundreds in stock, take your pick from some of the sickest decks available! Alien Workshop, Baker, Deathwish, Element, enjoi, Girl, Welcome. WKND, Santa Cruz, Primitive, and Real are among the most popular offered. Additionally, notable brands such as Almost, DGK, Flip, Krooked, Alien Workshop, Skate Mental, Zero, Creature, and Chocolate are available for all your skating needs.
The type of skating the rider wants to do will inform the board choice, which sometimes involves skating a non-popsicle shaped board. But if you are just starting out, you can simply start with the traditional popsicle shaped deck that you probably recognize. As you skate more and get to know what shapes you like or what kind of skateboarding you enjoy best, your decisions will take into account for company, shape, width, and style of riding. Until then, choosing a board by its graphic is totally acceptable. For an overview on types of skateboard decks and riding styles, check out our Skateboard Decks Section in our Buyer’s Guide. Once you find a deck you like, you can simply select the default wheels, trucks, bearings and grip tape or you have the option to make it a complete.
Hi, I can do an Ollie for 1 month already but somehow my Ollie is always unbalanced, meaning the front nose pops much higher than the back wheel. I understand that this is due to my front foot not sliding up higher, but I’m not sure how to correct it because my foot seem to get stuck after sliding up about an inch. Is it because of wrong technique or lack of calf muscles?
To summarize, a skateboarder's feet need to do two things successfully to complete an ollie. They need to provide a changing force to move the board correctly (so that the combined force of gravity and the skater's feet add up to the green arrows above), and they need to provide different amounts of force with each foot (shown by the red and blue arrows above) to steer and turn the board into the right orientation.
Invented in the late 1970s by Alan "Ollie" Gelfand, the ollie has become a skateboarding fundamental, the basis for many other more complicated tricks. In its simplest form, the ollie is a jumping technique that allows skaters to hop over obstacles and onto curbs, etc. What's so amazing about the ollie is the way the skateboard seems to stick to the skater's feet in midair. Seeing pictures of skaters performing soaring 4-foot ollies, many people assume that the board is somehow attached to the skater's feet. It's not. What's even more amazing about the ollie is that to get the skateboard to jump up, the skater pushes down on the board! The secret to this paradoxical maneuver is rotation around multiple axes. Let's take a closer look.
This ollie is commonly referred to as an “Ollie Nosebone.” First of all, you need good ollie skills. The key for this ollie is your front foot. When you reach the peak, (gently!) push your front foot forward not moving any other part of your body. That’s it, simple yet difficult. Of utmost importance is practicing your regular ollie over and over in various conditions so that extension tricks such as the ‘nosebone’ come almost naturally with experimentation. Nevertheless, here is a movie explaining how to do it.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.