If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
Hi, I can do an Ollie for 1 month already but somehow my Ollie is always unbalanced, meaning the front nose pops much higher than the back wheel. I understand that this is due to my front foot not sliding up higher, but I’m not sure how to correct it because my foot seem to get stuck after sliding up about an inch. Is it because of wrong technique or lack of calf muscles?

I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
If you’re looking for complete skateboards that are ready to go, then you’ve come to the right place. We’ve got a great range of boards that you can ride right away, and with our next day delivery service, you’ll have your board before you know it. Browse our great selection, which includes iconic brands such as Flip, and an incredible range of colourful Penny boards and deck graphics. With so many to choose from, we’re confident you’ll find the complete skateboard you’re looking for. Buy online today and benefit for our speedy service.

This was a simple purchase. No issues at all and the skateboards are really nice! Some people have said it comes unassembled, that's not the case. I ordered 2 different boards and both came assembled and ready to roll.. The boards are topped with grip tape and trucks and wheels were assembled perfectly. If I had a need to get another board I would run straight back to this kit, they are great!


Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂

The type of skating the rider wants to do will inform the board choice, which sometimes involves skating a non-popsicle shaped board. But if you are just starting out, you can simply start with the traditional popsicle shaped deck that you probably recognize. As you skate more and get to know what shapes you like or what kind of skateboarding you enjoy best, your decisions will take into account for company, shape, width, and style of riding. Until then, choosing a board by its graphic is totally acceptable. For an overview on types of skateboard decks and riding styles, check out our Skateboard Decks Section in our Buyer’s Guide. Once you find a deck you like, you can simply select the default wheels, trucks, bearings and grip tape or you have the option to make it a complete.
When I was about 10, I broke my first skateboard by riding it into a ditch. A decade later, in college, I broke another skateboard within an hour of owning it (surely a record) in a short-lived attempt at doing an ollie. (Surprisingly, the store accepted a return on that board even though it was in two pieces.) Then I was gifted a really nice, high-quality skateboard. The first thing I did with it was ride it down a big hill, a valiant but ill-fated adventure which ended with me jumping off the skateboard, rolling down the grass, and arriving scraped up, deflated, and rather disoriented near the entrance to my college cafeteria. (In my defense, the wheels and ball-bearings on that skateboard had been pre-lubricated to minimize friction, and why would anyone do that, that's just crazy.)

Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.[5]
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Pull your knees up into your chest – How far you actually want to pull your legs up is totally up to you, but the higher your feet go, the higher your board will go too. By the way, the highest recorded preferred stance ollie-pop is 45 inches, done by Aldrin Garcia, and the highest switch stance ollie-pop is 40.125 inches, by Gavin Caperton. And if you’re going for endurance rather than height, the record for most consecutive hops is held by Rob Dyrdek, who did 215 of them in a row on his TV show Rob and Big. So those give you something to shoot for.
If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.

The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
When I was about 10, I broke my first skateboard by riding it into a ditch. A decade later, in college, I broke another skateboard within an hour of owning it (surely a record) in a short-lived attempt at doing an ollie. (Surprisingly, the store accepted a return on that board even though it was in two pieces.) Then I was gifted a really nice, high-quality skateboard. The first thing I did with it was ride it down a big hill, a valiant but ill-fated adventure which ended with me jumping off the skateboard, rolling down the grass, and arriving scraped up, deflated, and rather disoriented near the entrance to my college cafeteria. (In my defense, the wheels and ball-bearings on that skateboard had been pre-lubricated to minimize friction, and why would anyone do that, that's just crazy.)

The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
The DreadXBoards Concave Skateboard has Plastic Deck Injection Molded for excellent durability. It features Urethane Wheels 59mm 78a, aluminum trucks, and Abec 7 Bearings. It is completely assembled and is ready to ride. It is perfect for beginners or experienced riders. It can load up to 185 lbs. It is great for kids and adults. It has an excellent rating of 4 on Amazon.
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
The Powell Golden Dragon 2 Skateboard is an affordable and complete skateboard for the beginners and also for the advanced skaters.  It has high-rebound, hand-cast polyurethane wheels to give you a great roll and grip.  It measures 7.5 inches wide with a colorful screen-printed bottom.  It is made in China and has an average rating of 4.2 on Amazon.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.
This set-up is awesome for its price!!!! The wheels are nice and smooth (a little too big for my liking, but still good). The bearings are average (I replaced them with bones REDS). The trucks are nice and sturdy, but the bushings are kinda weak. The board is AUTHENTIC and of good dimensions. Finally, the griptape...they're all pretty much the same it's just the brand name that's different, so it doesn't matter it's all good. I would buy from this seller over and over again!!!!!!!
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!

Penny Skateboards are available in 22", 27" and the 36" for different riding styles, skating abilities and personal preference. You can find a Penny board that's perfect for you and your skateboard needs. The 36" Penny Longboards allow you to carve up the streets, mountains or beach in style. Regardless of which size Penny is right for you, everyone needs a Penny skateboard to cruise on at the beach, the park, the shops or while on holidays.
101 5boro Adidas Alien Workshop Alltimers Almost Anti-Hero Arbor Bacon Skateboards Baker Birdhouse Black Label Blind Blood Wizard BLVD Chocolate Club Midnite Colours Collectiv Create Creature Darkstar DB Longboards Deathwish DGK Diamond Supply Co Dieta DOG Doom Sayers Club Element Enjoi Evisen Fancy Lad Flip Foundation Friendship Skateboards Girl Globe Grizzly Habitat Heritage Heroin Hopps Hosoi Skates H-Street Illegal Civilization Isle Krooked Landyachtz Lib Tech Loaded Lowcard Lurkville Madness Magenta Mini Logo Moonshine MFG Northern Company Numbers Edition Paisley Passport Pizza Plan B Polar Skate Co. Politic Powell Peralta Program Quartet Quasi Rayne Real RIPNDIP Santa Cruz Santa Monica Airlines Schmitt Stix Scram SCUMCO & Sons Sector 9 Shake Junt SK8MAFIA Skate Mental Sketchy Tank Sour SOVRN Square Up Stereo Tactics The Killing Floor Theories Tired Toy Machine Traffic Two Cents Skateboards Vision Welcome WKND Zero
After that I went to my regular Olley spot to practice, fell so hard three times. My legs were so fucked up from the day before. Now I feel like shit because I had problem with a 20cm ledge I landed at least 100 times up and down yesterday. I’m even capable of 50cm ledges at slow speed, but I only get the front wheel and the board up so I have to put pressure on the nose to get it all the way up.
!function(e){function n(t){if(r[t])return r[t].exports;var i=r[t]={i:t,l:!1,exports:{}};return e[t].call(i.exports,i,i.exports,n),i.l=!0,i.exports}var t=window.webpackJsonp;window.webpackJsonp=function(n,r,o){for(var s,a,l=0,u=[];l1)for(var t=1;td)return!1;if(p>f)return!1;var e=window.require.hasModule("shared/browser")&&window.require("shared/browser");return!e||!e.opera}function a(){var e="";return window.Q.sendErrorsToWeblogger&&"quora.com"==window.Q.subdomainSuffix&&(e+=[window.location.protocol,"//log.quora.com"].join("")),e+="/ajax/log_errors_3RD_PARTY_POST"}function l(){var e=o(h);h=[],0!==e.length&&c(a(),{errors:JSON.stringify(e)})}var u=t("./third_party/tracekit.js"),c=t("./shared/basicrpc.js").rpc;u.remoteFetching=!1,u.collectWindowErrors=!0,u.report.subscribe(r);var f=10,d=window.Q&&window.Q.errorSamplingRate||1,h=[],p=0,m=i(l,1e3),w=window.console&&!(window.NODE_JS&&window.UNIT_TEST);n.report=function(e){try{w&&console.error(e.stack||e),u.report(e)}catch(e){}};var y=function(e,n,t){r({name:n,message:t,source:e,stack:u.computeStackTrace.ofCaller().stack||[]}),w&&console.error(t)};n.logJsError=y.bind(null,"js"),n.logMobileJsError=y.bind(null,"mobile_js")},"./shared/globals.js":function(e,n,t){var r=t("./shared/links.js");(window.Q=window.Q||{}).openUrl=function(e,n){var t=e.href;return r.linkClicked(t,n),window.open(t).opener=null,!1}},"./shared/links.js":function(e,n){var t=[];n.onLinkClick=function(e){t.push(e)},n.linkClicked=function(e,n){for(var r=0;r>>0;if("function"!=typeof e)throw new TypeError;for(arguments.length>1&&(t=n),r=0;r>>0,r=arguments.length>=2?arguments[1]:void 0,i=0;i>>0;if(0===i)return-1;var o=+n||0;if(Math.abs(o)===Infinity&&(o=0),o>=i)return-1;for(t=Math.max(o>=0?o:i-Math.abs(o),0);t>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=0;r>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=new Array(s),i=0;i>>0;if("function"!=typeof e)throw new TypeError;for(var r=[],i=arguments.length>=2?arguments[1]:void 0,o=0;o>>0,i=0;if(2==arguments.length)n=arguments[1];else{for(;i=r)throw new TypeError("Reduce of empty array with no initial value");n=t[i++]}for(;i>>0;if(0===i)return-1;for(n=i-1,arguments.length>1&&(n=Number(arguments[1]),n!=n?n=0:0!==n&&n!=1/0&&n!=-1/0&&(n=(n>0||-1)*Math.floor(Math.abs(n)))),t=n>=0?Math.min(n,i-1):i-Math.abs(n);t>=0;t--)if(t in r&&r[t]===e)return t;return-1};t(Array.prototype,"lastIndexOf",c)}if(!Array.prototype.includes){var f=function(e){"use strict";if(null==this)throw new TypeError("Array.prototype.includes called on null or undefined");var n=Object(this),t=parseInt(n.length,10)||0;if(0===t)return!1;var r,i=parseInt(arguments[1],10)||0;i>=0?r=i:(r=t+i)<0&&(r=0);for(var o;r
×